Bosch Appliances WTXD5321US Electrical Connection, For U.S.A, Connecting, Power Supply, Cord

Straighten the grounding strap and hang loosely.

5½ inch (14 cm) must be provided on this side for pipes/brackets (see page 7).

-Distances above the indicated

minimum	dimensions	reduce the	1
risk of mold formation behind the
appliance.				2
- Additional distances reduce noise
transmission.
- Additional	distances	facilitate
installation	and service.				3

-If the dryer is installed in a small

room, the

doors of the room

mustWhen

installing

the

receptacle for the

be fitted with vents of a specified dryer cord, ensure

that the power

minimum

size.

supply

cord

is

accessible

when

the

1

-

terminal

block

dryer

is in the

installed position.

2

-

grounding

strap

The power cord should only be

replaced by

a

qualified person.

Use a

3

-

Angle bracket

for

strain relief

clamp

4owire

power

supply cord

(see

2.

Loosen the

bottom screw

of the

electrical connection

U.S.A.

below).

grounding strap.

Place the

screw

For U.S.A.

to the GROUND

location.

Your dryer comes without a power supply cord.The power cord must meet the following requirements:

-UL listed in the USA

- 208 p 240 volt rated (minimum)

-30 amps

-Type SRDT or DRT (UL 2158)

-Five feet long (minimum)

d WARNING

d

Power

cord

must

be connected

by a

3. Fix the

strain relief clamp to the

licensed

electrician

only.

angle bracket. Tighten

the nut.

Use only a U.L. approved

30 amp

power cord with strain relief clamp -

note

manufacturer's

instructions.

Do

not

plug end

of

power

cord into

a live receptacle before connecting

The

dryer

door

is delivered

with hinges

power cord to appliance terminals

on the

right.

If

required,

the

door

and

closing

junction/splitter box

as

hinges

can

be

switched

to

the

left

side.

described

below.

If the door hinges are to be changed

Do not reuse old power cord. Cord

over,

please

contact

your

dealer or

our

must have closed loop or upturned

customer

serviceoteam

(see page 20)

end

wire

terminating

connectors.

Do not make a sharp bend or crimp

Electrical

connection

wiring/conductor

at

connections.

Only

a

4oconductor

cord

shall

4. Loosen

the 2 screws labeledL and

d WARNING

d

be used

when

the

appliance

is

installed

in

a

mobile

home,

in

a

the screw labeledN in the terminal

recreational vehicle, in a new branch

block. and the screw of the

Power cord must be connected

by a

circuit installation

or

an

area where

GROUND

terminal.

qualified

person

only.

the

local

codes

do

not

permit

5. Thread

the 4 wire cable through th

Connect

to

individual Branch

grounding

through

the neutral.

U.L. strain

relief

clamp.

Circuit.

Connecting

4Wwire

power

supply

6. Tighten

the

screws (2.5 Nm)

of

the

Do not

use

an adapter.

U.L. strain

relief

clamp

so

that

the

cord

Do

not use an extension cord.

power

cord

cannot be

moved.

1. Remove

the

screws from

the

cover

Do

not

remove

ground

prong.

7. Attach

the

power

cord

ground

of the

terminal

block

located

at the

conductor

(green)

to the GROUND

For

CANADA

top

rear

of

the

appliance.

terminal. Tighten the screw (2.5

Your dryer comes with a power supply

Nm) so that the

ground conductor

cord, CSA listed in Canada.

is held

securely

in place.

The

Siemens

dryer requires a 4owire

receptacle.

6