Bostitch CAP1645-OF owner manual Glossary, Repairs, Full ONE Year Warranty

REPAIRS

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by a BOSTITCH factory service center, a BOSTITCH authorized service center or other qualified service personnel. Always use identical replacement parts.

FULL ONE YEAR WARRANTY

BOSTITCH heavy duty industrial tools are warranted for one year from date of purchase. We will repair, without charge, any defects due to faulty materials or workmanship. For warranty repair information, call 1-800-556-6696 . This warranty does not apply to accessories or damage caused where repairs have been made or attempted by others. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces.

Latin America: This warranty does not apply to products sold in Latin America. For products sold in Latin America, see country specific warranty information contained either in the packaging, call the local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT (Fig. 4) : If your warning labels become illegible or are missing, call 1-800-556-6696 for a free replacement.

FIG. 4

WARNING DRAIN TANK DAILY OR AFTER EVERY 4 HOURS OF US E. CONDENSATION BUILD-UP MAY CAUSE CORROSION INSIDETANK RESULTING INTANK FAILURE. SEE MANUAL FOR INSPECTION PROCEDURES.

TO DRAIN TANK OPEN VALVE SLOWLY AND TILT COMPRESSORTO EMPTY ACCUMULATED WATER.

ADVERTENCIA DRENE ELTANQUE A DIARIO O DESPUÉS DE CADA 4 HO RAS DE USO. LA ACUMULACIÓN DE CONDENSACIÓN PUEDE O CASIONAR CORROSIÓN DENTRO DEL TANQUE Y PROVO CAR FALLA DEL

TANQUE. CONSULTE EL MANUAL PARA CONOCER LOS PROCEDIMIENTOS DE INSPECCIÓN. PARA DRENAR EL TANQUE, ABRA LA VÁLVULA LENTAMENTE E INCLINE ELCOMPRESOR PARAELIMINAR EL AGUA ACUMULADA.

WARNING HOT SURFACES ADVERTENCIA SUPERFICIESCALIENTES

RÉSERVOIR DE VIDANGE QUOTIDIEN OU APRÈS TOUTES LES 4 HEURES D'UTILISATION.	AVERTISSEMENT SURFACES CHAUDES
AVERTISSEMENT L'HABILLAGE DE CONDENSATION PEUT CAUSER LA CORROSION À L'INTÉRIEUR DU RÉSERVOIR AYANT
POUR RÉSULTAT L'ÉCHEC DE RÉSERVOIR. VOIR LE MANUEL POUR DES PROCÉDURES D'INSPECTION. À LA VALVE
OUVERTE DE RÉSERVOIR DE VIDANGE LENTEMENT ET AU COMPRESSEUR D'INCLINAISON ÀL'EAU ACCUMULÉE VIDE.

CAUTION	ATENCIÓN	ATTENTION
DO NOT OPERATE IN UPRIGHT	NO OPERE LA HERRAMIENTA EN	NE PAS FAIRE FONCTIONNER EN POSITION
POSITION. UPRIGHT POSITION	POSICIÓN VERTICAL. SÓLO	VERTICALE. LA POSITION VERTICALE EST
IS FOR STORAGE ONLY.	ALMACENE EN ESTA POSICIÓN.	RÉSERVÉE AU STOCKAGE UNIQUEMENT.

WARNING

DO NOT ADJUSTFACTORY SETTINGS. TO REDUCE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER.

Pressure controls set at factory for maximum sa fe operation.

ADVERTENCIA

NO HAGA CAMBIOS ENLOS AJUSTES DE FÁBRICA. NO RETIRE LATAPA PARA REDUCIR EL RIESGO DE CHOQUE ELÉ CTRICO. Los controles de presión se ajustan en la fábrica para máxima seguridad en la ope ración.

AVERTISSEMENT

GLOSSARY

CFM: Cubic feet per minute.

SCFM: Standard cubic feet per minute; a unit of measure of air delivery.

PSI: Pounds per square inch; a unit of measure of pressure.

KPA (KILOPASCAL): Metric pressure measurement. 1 kilopascal equal 1000 pascals.

CODE CERTIFICATION: Products that bear one or more of the following marks: UL®, CUL, CULUS,

ETL®, CETL, CETLUS, have been evaluated by OSHA certified independent safety laboratories and meet the applicable Standards for Safety.

*UL® is a registered trademark of Underwriters Laboratories and ETL® is a registered trademark of Electrical Testing Laboratories.

CUT-IN PRESSURE: While the motor is off, air tank pressure drops when accessory is used. When the tank pressure drops to a certain low level the motor will restart automatically. The low pressure at which the motor automatically restarts is called cut-inpressure.

CUT-OUT PRESSURE: When an air compressor is turned on and begins to run, air pressure in the air tank begins to build. It builds to a certain high pressure before the motor automatically shuts off, protecting your air tank from pressure higher than its capacity. The high pressure at which the motor shuts off is called cut-outpressure.

Branch Circuit: The circuit carrying electricity from electrical panel to outlet.

14