Breville BMF600XL Issue - E11 manual Min Max, Using the ‘COLD STIR’ Setting

OPERATING YOUR BREVILLE Milk Café™

OPERATING YOUR BREVILLE Milk Café™

4.Pour the required amount of cold, fresh (or freshly opened) milk into the milk jug then cover with the jug lid. Always use cold milk and fill the milk jug between the MIN and MAX level markings. Overfilling may result in spillage, while underfilling prevents the frothing disc from working optimally.

NOTE

Never operate without the minimum level of liquid in the milk jug. The milk frother will automatically turn off if the milk jug is empty. If this occurs, you will need to wait for the milk frother to cool down before re-use, refer to page 14.

MIN MAX

For optimum results, there are different measurement markings within the milk jug. The chart on the right shows the approximate number of cups produced at each of the measurement markings. This is a guide only as the frothing disc selected and the type of milk, for example whole milk (vitamin D), 2%, 1%, fat-free, half-and-half etc., can create different amounts of froth.

JUG MARKING	FROTHING DISC	MAKES
		APPROX.
HOT CHOC MAX	Cappuccino	3 cups
25 fl.oz (750ml)	(recommended)
	OR
	Latte
CAPP / LATTE MAX	Cappuccino	2-3 cappuccinos
16 fl.oz (500ml)	OR
	Latte
8 fl.oz (250ml)	Cappuccino	1-2 cappuccinos
	OR
	Latte
MIN	Cappuccino	1 cappuccino
	OR
	Latte

NOTE

For optimum froth, do not exceed the CAPP/LATTE MAX (16 fl.oz, 500ml) measurement marking inside the milk jug.

5.Ensure the jug lid is securely attached and the outside of the milk jug is clean. Place the milk jug onto the power base, ensuring the jug is sitting flat.

6.Turn the START STOP push-dial to the desired temperature. When frothing milk for a cappuccino or latte, we recommend staying within the ‘OPTIMUM MILK TEMP’ range, however this is up to your personal preference.

If the temperature setting is changed during operation, the milk frother will stop at the new temperature selected.

The exception is if a lower temperature is selected mid-cycle and the milk has already exceeded the lower temperature. In this case, the milk frother will immediately stop.

ONLY PRESS ONCE, FIRMLY

7.Only press the START STOP push-dial once, firmly.. Frothing has started once the milk frother beeps once and the button surround slowly flashes. If the milk frother does not do this, try pushing the START STOP push-dial again to ensure it has been properly activated.

NOTE

Do not remove the milk jug from the power base during operation. Doing so may dislodge the frothing disc and cause a grinding noise. Always press the center of the START STOP push-dial before removing the jug. Operation has stopped once the button surround has stopped flashing.

WARNING

Appliance surfaces will be hot during and after operation.

8.When the milk has reached the selected temperature, the milk frother will automatically stop and beep twice. This will take anywhere between 2 -7 minutes depending on the quantity of milk used. Carefully remove the milk jug from the power base as the milk jug and contents will be hot. Be careful not to place the milk jug on a table cloth, plastic surface or heat sensitive surface which may scorch or melt. Remove the jug lid, pour and/or spoon out the frothed milk.

9.Clean the milk jug and frothing disc immediately after use. Both will be hot, so follow the instructions on page 17 and allow them to cool completely before disassembling.

NOTE

When frothing multiple batches, to prevent the Boil Dry Protection from activating (see page 14), we recommend allowing the milk jug to cool for approximately 5 minutes, or filling the milk jug with water for faster cooling. For best results, we also recommend cleaning the milk jug and frothing disc before re-use.

NOTE

After frothing the first batch of milk you may notice the power base begin to hum. This is normal. It is the cooling fan preventing the milk frother from overheating and will automatically cease to hum once adequately cooled. During this time, you may still use the milk frother unless the Boil Dry Overheat Protection as been activated

(see page 14).

USING THE ‘COLD STIR’ SETTING

The ‘Cold Stir’ setting allows you to stir already cold or hot milk without additional heat.

Use it to froth milk for cold beverages such as an iced cappuccino; to blend in syrups and flavorings for an iced chocolate or mocha; or to stir in dissolvable instant drinking powders into milk or water.

The ‘Cold Stir’ setting will operate for 60 seconds before automatically stopping. You can re-select the ‘Cold Stir’ setting if desired.

12 13