Turn on the machine | Brother 855-X06 manual

———————

1	1
	1
	2
1 Pull the thread
in completely.	3
	3

1 Pre-tension disk

2 Bobbin winder shaft

3 Bobbin

1Pull up the spool pin and put a spool of thread on this pin.

2While holding the thread from the spool with your right hand, pass the thread toward you, in the groove on the thread guide. Then, pass the thread around the pre-tension disk and pull the thread in completely.

1

1Pre-tension disk

CAUTION

●If the spool of thread is in the wrong place, or is set incorrectly, the thread may tangle on the spool pin.

3Pass the end of the thread through the hole on the bobbin from the inside of the bobbin.

4Put the bobbin onto the bobbin winder shaft and slide the bobbin winder shaft to the right. Turn the bobbin clockwise, by hand, until the spring on the shaft slides into the notch of the bobbin.

•Make sure to pull out 7 to 10 cm (3-4 inches) of thread from the hole on the bobbin.

3

1

2

1Spring on the shaft

2 Notch

3 7-10 cm (3-4 inches)

CAUTION

●Pull the thread taut and hold the end of the thread straight up. If the thread is too short, not pulled taut or held at an angle, injuries may occur when the thread is wound around the bobbin.

5Turn on the machine.

14

Image 15

Brother 855-X06 operation manual Pull up the spool pin and put a spool of thread on this pin, Turn on the machine

Contents

Sewing Machine Important Safety Instructions Save These Instructions Contents Part Name Part Code Americas Others AccessoriesOptional accessories Knowing Your Sewing Machine Flat bed attachment Main Parts Using Your Sewing Machine Connecting plugsConnect the foot controller plug to the machine Replacing the needle Main power and sewing light switchFoot controller Checking the needle Changing the presser foot Stretch stitching Presser foot installation orientationControls Pattern selection dial Pattern Stitch Name Recommended Patterns and stitch namesStitches Only available on certain models Stitches 0-3/16 Fixed Stitch width dial Stitch length dial Threading the Machine Reverse sewing leverWinding the bobbin Turn on the machine Pull up the spool pin and put a spool of thread on this pin Lower threading Install the bobbin wound with thread Groove Projection Lower threading for models equipped with a quick-set bobbin Upper threading Guide Turn off the machine Raise the presser foot lever Needle holder Needle threader lever Pull the thread through the needle Replace the bobbin cover Drawing up the lower threadPull on the upper thread to draw up the lower thread For models equipped with a quick-set bobbin Fabric Type/Application Thread Size of Needle FABRIC, THREAD, and Needle CombinationsBall point needle Transparent nylon thread Sewing Basics Please read before sewingStarting sewing Trial sewing Changing the sewing DirectionSewing thick fabrics Sewing with a twin needle Option Sewing thin fabricsSewing stretch fabrics Stitching cylindrical pieces Thread the right needle Attaching the extra spool pinSelect a stitch Thread the left needle Upper tension is too tight Thread tensionUpper tension is too loose Correct tension Blind hem stitching BUILT-IN StitchesStraight stitching Zigzag stitching Fold the fabric along the desired edge of the hem, and press Adjust the thread tension so that it is tighter than normal Elastic stitchingSew at a slow speed Set the stitch width to Double action stitchingFagoting Joining fabric Overedge stitching Pattern StitchStitch Stitch Name Pattern Feather stitchingTriple zigzag stretch stitching Decorative stitching Openbutton.the button plate and insert Sewing Buttonholes and ButtonsMaking a buttonhole 1-step automatic buttonhole Making a buttonhole If the button does not fit in the button guide plate You need to sew the front bar tack firstLower the buttonhole lever and push it back slightly Piece of fabric to observe how Material is fed Adjusting buttonholesMaking a buttonhole on stretch fabrics Follow steps 1 to 6 from Making a buttonhole on Any Sewing Darning Sewing buttonsAt a slow speed, sew about 10 stitches Then tie it with the bobbin thread Prepare the fabric with the zipper basted on the wrong side Using Attachments and ApplicationsWhen you have finished sewing, remove the basting stitching Zipper insertion Baste the cut design to the fabric GatheringDarning Appliqués When sewing seams Turn off the machine Optional AccessoriesUsing the blind stitch foot When edge stitching Turn off the machine Appendix MaintenancePrecautions on storing the machine Cleaning Install the needle plate, and then tighten the screws Symptom Possible cause How to put it right Troubleshooting Tangled or Thread BreaksLower Thread is Stitch is Stitches are SkippedThreader can Not be used Numerics Index English