Groove Projection | Brother 855-X06 specification

———————

4Put the bobbin in so the thread comes out in the direction shown by the arrow.

CAUTION

●Make sure you set the bobbin so the thread unrolls in the right direction. If the thread unrolls in the wrong direction, it may cause the thread tension to be incorrect or break the needle.

5Hold the end of the thread, push the bobbin down with your finger, and then pass the thread through the slit, as shown.

•If the thread is not correctly inserted through the tension-adjusting spring of the bobbin case, it may cause incorrect thread tension.

1

1Tension-adjusting spring

6Replace the bobbin cover. Put the projection into the race retainer groove

and push closed.	1
	1
1
2

1Groove

2 Projection

•Make sure that the end of the thread comes out from the cover toward the rear of the machine (as shown in the illustration).

•Draw up the lower thread before starting sewing. Refer to “Drawing up the lower thread” on page 21 after threading the upper thread.

Lower threading (for models equipped with a quick-set bobbin)

Install the bobbin wound with thread.

This feature is only available on certain models.

1Follow steps 1 to 4 from “Lower threading” on page 15.

2While lightly holding down the bobbin with your right hand as shown, guide the thread through the slit (1 and 2). Then, pull the thread toward you to cut it with the cutter (3).

•At this time, check that the bobbin easily rotates counterclockwise.

	2
1
2	3	1
		1

1Slit

2Cutter (Cut the thread with the cutter.)

16

Image 17

Brother 855-X06 operation manual Lower threading for models equipped with a quick-set bobbin, Groove Projection

Contents

Sewing Machine Important Safety Instructions Save These Instructions Contents Optional accessories AccessoriesKnowing Your Sewing Machine Part Name Part Code Americas Others Flat bed attachment Main Parts Connect the foot controller plug to the machine Using Your Sewing MachineConnecting plugs Foot controller Main power and sewing light switchChecking the needle Replacing the needle Changing the presser foot Controls Presser foot installation orientationPattern selection dial Stretch stitching Stitches Only available on certain models Patterns and stitch namesStitches Pattern Stitch Name Recommended 0-3/16 Fixed Stitch width dial Stitch length dial Winding the bobbin Threading the MachineReverse sewing lever Turn on the machine Pull up the spool pin and put a spool of thread on this pin Lower threading Install the bobbin wound with thread Groove Projection Lower threading for models equipped with a quick-set bobbin Upper threading Guide Turn off the machine Raise the presser foot lever Needle holder Needle threader lever Pull the thread through the needle Pull on the upper thread to draw up the lower thread Drawing up the lower threadFor models equipped with a quick-set bobbin Replace the bobbin cover Ball point needle FABRIC, THREAD, and Needle CombinationsTransparent nylon thread Fabric Type/Application Thread Size of Needle Starting sewing Sewing BasicsPlease read before sewing Sewing thick fabrics Trial sewingChanging the sewing Direction Sewing stretch fabrics Sewing thin fabricsStitching cylindrical pieces Sewing with a twin needle Option Select a stitch Attaching the extra spool pinThread the left needle Thread the right needle Upper tension is too loose Thread tensionCorrect tension Upper tension is too tight Straight stitching BUILT-IN StitchesZigzag stitching Blind hem stitching Fold the fabric along the desired edge of the hem, and press Sew at a slow speed Adjust the thread tension so that it is tighter than normalElastic stitching Fagoting Double action stitchingJoining fabric Set the stitch width to Stitch Overedge stitchingPattern Stitch Triple zigzag stretch stitching Feather stitchingDecorative stitching Stitch Name Pattern Making a buttonhole 1-step automatic buttonhole Sewing Buttonholes and ButtonsMaking a buttonhole Openbutton.the button plate and insert Lower the buttonhole lever and push it back slightly If the button does not fit in the button guide plateYou need to sew the front bar tack first Making a buttonhole on stretch fabrics Adjusting buttonholesFollow steps 1 to 6 from Making a buttonhole on Piece of fabric to observe how Material is fed At a slow speed, sew about 10 stitches Sewing buttonsThen tie it with the bobbin thread Any Sewing Darning When you have finished sewing, remove the basting stitching Using Attachments and ApplicationsZipper insertion Prepare the fabric with the zipper basted on the wrong side Darning GatheringAppliqués Baste the cut design to the fabric Using the blind stitch foot Optional AccessoriesWhen edge stitching Turn off the machine When sewing seams Turn off the machine Precautions on storing the machine MaintenanceCleaning Appendix Install the needle plate, and then tighten the screws Symptom Possible cause How to put it right Troubleshooting Lower Thread BreaksThread is Tangled or Threader can Stitches are SkippedNot be used Stitch is Numerics Index English