Manuals / Brands / Household Appliance / Sewing Machine / Brother / Household Appliance / Sewing Machine

Brother 885-X36, 885-X38 Lower threading, bPress the foot controller to start, 3Remove the bobbin cover by sliding it and lift toward you

1 52

Download 52 pages, 17.8 Mb

———————

bPress the foot controller to start.

cWhen the bobbin seems full and begins spinning slowly, take your foot off the foot controller.

CAUTION

●When the bobbin winding becomes slow, stop the machine, otherwise the sewing machine may be damaged.

dCut the thread, slide the bobbin winder shaft to the left, and then remove the bobbin from the shaft.

Note

●When the sewing machine is started or the handwheel is turned after winding the thread around the bobbin, the machine will make a clicking sound; this is not a malfunction.

●The needle bar does not move when you slide the bobbin winder shaft to the right.

CAUTION

●Not winding the bobbin properly may cause the thread tension to loosen, and may break the needle.

12

1Wound evenly

2 Wound poorly

Lower threading

Install the bobbin wound with thread.

1

CAUTION

●Make sure you turn off the machine while threading. If you accidentally step on the foot controller and the machine starts to sew, you could be injured.

1Prepare the bobbin wound properly before threading the lower thread.

•See page 13 for the details about bobbin winding.

2Raise the needle by turning the handwheel toward you (counterclockwise) and raise the presser foot lever.

3Remove the bobbin cover by sliding it and lift toward you.

1

1Bobbin cover

4Put the bobbin in so the thread comes out in the direction shown by the arrow.

CAUTION

●Make sure you set the bobbin so the thread unrolls in the right direction. If the thread unrolls in the wrong direction, it may cause the thread tension to be incorrect or break the needle.

16

Contents

http://solutions.brothe r.c Please read these safety instructions before attempting to use the machine Always Do not Never Never This machine is intended for household use FOR USERS IN THE UK, EIRE, MALTA AND CYPRUS ONLY IMPORTANT CONTENTS 1 KNOWING YOUR SEWING MACHINE ACCESSORIES Optional accessories THE MAIN PARTS Flat bed attachment USING YOUR SEWING MACHINE Connecting plugs Main power and sewing light switch Foot controller Checking the needle Replacing the needle Changing the presser foot THE CONTROLS Pattern selection dial Stretch stitching Patterns and stitch names Page Stitch length dial Stitch width dial Reverse sewing lever Feed dog position switch THREADING THE MACHINE Winding the bobbin 1Turn on the machine 3Slide the bobbin winder shaft to the right until it snaps into place 4Swing up the spool pin, and then remove the spool cap Slide the spool cap onto the spool pin Memo Lower threading Page Upper threading 5Fully insert the spool for the upper thread onto the spool pin 6Slide the spool cap onto the spool pin 8Pass the thread under the thread guide B from the back to the front bLower the presser foot lever gRaise the needle threader lever Drawing up the lower thread 5Pull on the upper thread to draw up the lower thread 7Replace the bobbin cover FABRIC, THREAD, AND NEEDLE COMBINATIONS 2SEWING BASICS Please read before sewing Starting sewing Trial sewing Changing the sewing direction Sewing thick fabrics Sewing thin fabrics Sewing stretch fabrics Stitching cylindrical pieces Sewing with a twin needle (Option) ■Attaching the extra spool pin ■Twin needle threading 2Thread the left needle 3 Thread the right needle 4Attach zigzag foot “J” Thread tension 3BUILT-INSTITCHES Straight stitching Zigzag stitching Blind hem stitching 2Fold the fabric along the desired edge of the hem, and press 6 Remove the flat bed attachment and make free-armsewing possible Shell tuck stitching Elastic stitching Double action stitching Fagoting Overedge stitching Feather stitching Triple zigzag stretch stitching Decorative stitching 4SEWING BUTTONHOLES AND BUTTONS Making a buttonhole (1-stepautomatic buttonhole) 5 You need to sew the front bar tack first 6Lower the buttonhole lever and push it back slightly 7While gently holding the upper thread, start the machine 8The bar tacks of the buttonhole are sewn in the order shown Adjusting buttonholes Sewing buttons 5USING ATTACHMENTS AND APPLICATIONS Zipper insertion Gathering Darning Appliqués Using the blind stitch foot 6APPENDIX MAINTENANCE Restrictions on oiling Precautions on storing the machine Cleaning 8Install the needle plate, and then tighten the screws TROUBLESHOOTING Page Page INDEX