Manuals / Brother / Household Appliance / Sewing Machine

Brother XL-2620, XL-3510, XC6771-021 operation manual Wound evenly Wound poorly

Models: XC6771-021 XL-2620 XL-3510

1 51

Download 51 pages 58.87 Kb

Page 19

XL2600.book Page 17 Thursday, November 4, 2004 9:46 PM

4While holding the end of the thread, gently press the foot controller to wind the thread around the bobbin a few times. Then stop the machine.

5Trim the excess thread above the bobbin.

6Press the foot controller to start.

7When the bobbin seems full and begins spinning slowly, take your foot off the foot controller.

8Cut the thread, slide the bobbin winder shaft to the left and remove the bobbin.

Note

●The needle bar does not move when you slide the bobbin winder shaft to the right.

●Immediately after winding the bobbin, it is normal to hear the sound of the clutch engaging when beginning to sew or turning the handwheel.

CAUTION

●Make sure you follow the instructions carefully. If you do not cut the excess thread completely before winding the bobbin, when the thread runs low it may tangle around the bobbin and cause the needle to break.

CAUTION

●Not winding the bobbin properly may cause the thread tension to loosen, and may break the needle.

12

1Wound evenly

2 Wound poorly

1

17

Image 19

Brother XL-2620, XL-3510, XC6771-021 operation manual Wound evenly Wound poorly

Contents

Appendix Important Safety Instructions For Users in the UK, EIRE, Malta and Cyprus only Please Read These Instructions Before YOU USE the Machine UNPACKING/REPACKING InstructionsContents Using Attachments and Applications Main Parts Knowing Your Sewing MachineOptional Accessories AccessoriesConnecting Plugs Using Your Sewing MachineReplacing the Needle Main Power and Sewing Light SwitchFoot Controller Checking the NeedleTouches the stopper, and securely tighten Changing the Presser Foot1Slide the flat bed attachment to the left to release it Using a Free-arm StyleFlat Bed Attachment 1Slideopen theit. flat bed attachment to the left toPattern Selection Dial ControlsStitches Width Patterns and Stitch NamesPattern Recommended Instruction3/16 Fixed 3/32 Stitch Length Dial Stitches Selecting a Stretch Stitch Stretch StitchingStitch Width Dial Reverse Sewing LeverWinding the Bobbin Threading the MachineWound evenly Wound poorly Lower Threading Lower Threading for models equipped with a quick-set bobbin Follow steps 1 and 2 from Lower Threading Upper Threading Raise the presser foot using the presser foot leverPullon thisup pin.the spool pin and put a spool of thread 6Putneedle.the thread behind the guide above Hook Thread Sewing with a Twin Needle Drawing up the Lower ThreadThread Tension Fabric Type Thread Size of Needle FABRIC, THREAD, and Needle CombinationsSize Fixed 16-0 Please Read Before SewingStraight Stitching PatternZigzag Stitch Zigzag StitchingStitch Stitch Name Zigzag Stitch1Bothfabric.threads should be the same color as Blind Hem StitchingShell Tuck Stitching Stitch4Sew at a slow speed Elastic StitchingStitch Double Action StitchingPatchworking Overedge StitchingTriple Zigzag Stretch Stitching Feather StitchingDecorative Stitching Stitch Pattern Making a ButtonholePattern Adjusting Buttonholes Stitch Sewing ButtonsWidth Foot Zipper InsertionCenter Any GatheringDarning OtherZigzag Stitch Any AppliquésMonogramming Embroidering Stitch WidthKeep fingers away from moving parts, especially needles Using the Walking Foot Optional AccessoriesStitch Plate Using the Quilting FootQuickly Stitch Together a Quilt Using the 1/4-inch Quilting FootMachine’s sewing speed. Sew while moving the fabric slowly 16-3/32Put the light cover back on and fasten the screw MaintenanceCleaning Changing the Light Bulb0Install the needle plate cover Symptom Possible cause How to put it right Reference TroubleshootingFabric is LowerOr breaks Thread tenPitched noise While sewing Stitches areSkipped There is a highNumerics Index