SERVICE (cont.)

AUGER SHAFT ASSEMBLY

Auger Motor Cover

 

Run Capacitor

 

Auger Motor Assy

 

Auger Shaft Assy

 

Ceramic Coating

Hopper Drum Seal

 

Auger Shaft Bushing

Cooling Drum Seal

Cooling Drum

 

FIG. 5 AUGER SHAFT ASSEMBLY

P1758

 

Location:

The Auger Shaft Assembly is located in each of the cooling drums.

Removal and Replacement:

1.Drain, remove and clean hopper; refer to the Rec- ommended Daily Weekly Cleaning Section of this manual, for proper cleaning procedures. Discard the hopper/drum seal and faucet seal.

2.Remove the #8 locking screws securing auger motor cover to the cooling drum mount assembly; remove cover and set aside for reassembly.

3.Remove the #8 locking screw on the lower right side (viewed from front) of the auger motor mounting bracket securing the auger motor run capacitor. Set capacitor aside with wires attached.

4.Disconnect the auger motor terminal from the terminal on the main wiring harness.

5.Remove the remaining #8 locking screws securing the auger motor mounting bracket to cooling drum mounting bracket.

6.Remove motor with mounting bracket, split pin and torsion spring bearing as an assembly.

NOTE - When removing or installing motor and shaft assemblies, be sure the split pins are turned to a posi- tion that will clear the torque sensor circuit board.

7.Pull the auger shaft assembly straight out of cool- ing drum. Inspect the shaft for abnormal wear or scoring.

8.From the front of dispenser, remove the seal and blue bushing from cooling drum and discard them.

9.Clean seal and bushing surfaces of the cooling drum very thoroughly.

10.Refer to Fig 6 and slip new blue bushing into cooling drum.

Blue bushing

Do NOT get any Lube on this surface (between Drum and Bushings/Seals)

P1759

FIG. 6 AUGER SHAFT BUSHING

11.Place seal on insertion tool #28395.0000, as shown in Fig. 7. Make sure open face of seal is toward cooling drum.

12.Push seal into bore until it is firmly seated; remove tool.

13.Place a small amount of #29563.0000 “Krytox” lubricant (provided in kit in a plastic cap) on the end of the motor shaft (about 1 1/2”) and a thin film in the groove. Install auger shaft assembly onto the motor shaft. See Fig. 8. Do not use too much “Krytox” lubricant.

NOTE - This is the only place “Krytox” lubricant is used.

25

41084 102709

 

Page 24 Page 26
Page 25
Image 25
Bunn ULTRA-2 manual Auger Shaft Assembly
Page 24 Page 26

ULTRA-2 specifications

The Bunn ULTRA-2 is an exceptional frozen beverage dispenser that caters to both commercial and home use, making it a popular choice in various establishments such as cafes, restaurants, and convenience stores. Renowned for its reliability and efficiency, the ULTRA-2 serves a wide range of frozen beverages, including slushes, smoothies, and frozen cocktails, providing an irresistible treat for customers.

One of the standout features of the Bunn ULTRA-2 is its high-capacity design. With a dual hopper system, this machine allows operators to serve two different flavors simultaneously. Each hopper can hold up to 3.2 gallons of product, allowing for continuous service without the need for frequent refills. This is particularly advantageous during peak hours when demand is high.

The ULTRA-2 is equipped with Bunn's advanced refrigeration technology, which ensures rapid freezing and consistent product quality. The machine uses a patented freezing mechanism that maintains optimal product texture and temperature, resulting in a smooth, uniform consistency that keeps customers coming back for more. Additionally, the ULTRA-2's adjustable temperature control allows operators to customize the consistency of the beverages to their liking.

User-friendliness is another hallmark of the Bunn ULTRA-2. The machine features intuitive controls that simplify operation, making it easy for staff to learn and use efficiently. A built-in safety feature prevents the machine from operating when the hoppers are too low, minimizing waste and ensuring product quality.

Durability and ease of maintenance are also prominent characteristics of the ULTRA-2. Constructed from high-quality stainless steel, the machine offers enhanced longevity and is resistant to rust and corrosion. The removable hoppers and door assemblies facilitate quick cleaning and maintenance, allowing businesses to keep the machine in top working condition with minimal effort.

In summary, the Bunn ULTRA-2 stands out in the crowded market of frozen beverage dispensers through its dual hopper functionality, advanced refrigeration technology, user-friendly design, and robust construction. Whether for a busy café or a family gathering, the ULTRA-2 provides a reliable solution for delivering delicious frozen beverages that satisfy a variety of tastes and preferences.
Top Page Image Contents