Manuals / Bush Hog / Lawn and Garden / Compact Loader

Bush Hog 2347 QT manual Carrying The Load

Models: 2347 QT

1 31

Download 31 pages 45.57 Kb

Page 16

CARRYING THE LOAD

CARRYING THE LOAD

Position the bucket as low as possible below the level of the tractor hood for maximum stability and visibility, whether the bucket is loaded or empty.

Use extreme caution when operating the loader on a slope and keep the bucket as low as possible. This keeps the bucket and tractor center of gravity low and will provide maximum tractor stability.

CAUTION

OPERATING THE LOADER ON A HILLSIDE IS DANGEROUS. EXTREME CARE IS RECOMMENDED.

DUMPING THE BUCKET

Lift the bucket high enough to clear the side of the vehicle. Move the tractor in as close to the side of the vehicle as possible, then dump the bucket.

LOWERING THE BUCKET

After the bucket is dumped, back away from the vehicle while lowering and rolling back the bucket.

FLOAT POSITION

DUMP

LOWER

DO THIS	NOT THIS

1-LEVER

CONTROL

ROLLBACK

FLOAT POSITION

RAISE

When transporting the load, keep the bucket as low as possible to avoid tipping, in case a wheel drops in a rut.

NOT THIS

DO THIS

DUMP

LOWER

2-LEVERROLLBACK

CONTROLSRAISE

14

Image 16

Bush Hog 2347 QT manual Carrying The Load

Contents

1207 $4.0050057986 OPERATION MAINTENANCECONGRATULATIONS TABLE OF CONTENTS RETAIL CUSTOMER’S RESPONSIBILITY UNDER THE BUSH HOG WARRANTYUNDERSTAND SIGNAL WORDS SECTION/PARATHIS LIMITED WARRANTY SHALL NOT APPLY DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGESLIMITED WARRANTY OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO2347 QT LOADER IT IS RECOMMENDED THAT TRACTOR BEEQUIPPED WITH ROLLOVER PROTECTIVE SYS TEM ROPS AND SEAT BELT BE USED FOR ALL LOADER OPERATIONSTHE TRACTOR IMPORTANT SAFETY PRECAUTIONSTHE LOADER SAFETY PRECAUTIONS CONTINUED OPERATING THE LOADEREMPLOYERS, EMPLOYEES AND OPERATIONS EMPLOYEE TRACTOR OPERATING INSTRUCTIONSIMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING This Act Seeks1-1 INTRODUCTION SECTION INTRODUCTION AND DESCRIPTION1-2 DESCRIPTION Table 1-1 TECHNICAL SPECIFICATIONS SERIES LOADERSECTION LOADER MOUNTING AND DISMOUNTING 2-1 PREPARING TRACTOR2-2 MOUNTING LOADER TO AVOID INJURY OR DEATHH. Tighten nut retaining cuff to 85 ft./lbs DO NOT STAND UNDER LOADER WHILE REMOVING/INSTALLING PARKING STANDSTighten Nut To 85 ft./lbs 2-3 DISMOUNTING LOADER DO NOT STAND UNDER LOADER WHILE REMOVING/INSTALLING PARKING STANDSSECTION OPERATING INSTRUCTIONS 3-1 GENERAL SAFETY3-2 OPERATION CAUTON DO NOT ATTEMPT TO LIFT BUCKET LOADS IN EXCESS OF CAPACITIES CAUTONLISTED IN TABLE 1-1 TECHNICAL SPECI FICATIONS CARRYING THE LOAD OPERATING WITH FLOAT CONTROL FLOATSidecutting is a good technique for cutting down a big pile FLOAT SURFACE MATERIAL LOADING FROM A BANKPEELING AND SCRAPING 6” 3RD CUT , 4TH CUT, ETCLOADING LOW TRUCKS OR SPREADERS FROM A PILE BACKFILLING3-3 BALE SPEAR OPERATION Handling large heavy objects can be extremely dangerous due toH Possibility of rolling the tractor over H Possibility of upending the tractor3-4 FORK LIFT OPERATION 3-5 QUICK HITCH OPERATION3-6 TRANSPORTING H TRANSPORT LOADS LOW AND SLOW H AVOID CONTACT WITH POWER LINESSECTION MAINTENANCE 4-1 MAINTENANCE CHECK LIST4-2 LUBRICATION Figure 4-3 HYDRAULIC SYSTEM PRESSURE REQUIREMENTS4-4 TROUBLESHOOTING TABLE 4-1 TROUBLESHOOTING PROCEDURESPROBLEM POSSIBLE CAUSEASSEMBLY 5-1 MAINFRAME ASSEMBLYSECTION THE FOLLOWING SAFETY PRECAUTIONSFigure 5-2 Parking Stands Installed Figure 5-4 Cuff Arrangement 5-2 OPTIONAL HYDRAULIC VALVE STAND ASSEMBLY Figure 5-3 OPTIONAL HYDRAULIC VALVE PLUMBING INSTRUCTIONS HOSE COLOR CODES5-4 BASIC POWER BEYOND PLUMBING INSTRUCTIONS 5-6 BALE SPEAR OPTION 5-5 FORK LIFT OPTION5-7 TINE TEETH SAFETY DECALS REAR VIEW OF SUBFRAME25H46071 79104 79103 24-6-423 25H46010TORQUE SPECIFICATIONS AMERICANMETRIC Bolt Head Markings