Manuals / Bush Hog / Lawn and Garden / Compact Loader

Bush Hog 2347 QT manual Fork Lift Option, Bale Spear Option, Tine Teeth

Models: 2347 QT

1 31

Page 28

5-5 FORK LIFT OPTION

Raise the positioning lock pins at the top of each fork. Place fork in the middle of the frame over the notch in the lower edge. Slide forks to desired posi-

tions and lower pins to lock forks in place.

Guard

Mainframe

Lock Pin

Forks

5-6 BALE SPEAR OPTION

Insert long spear into top of frame and fasten with eccentric nut as shown. Tapered side of nut must be against frame. Torque nut to 470 -505 ft./lbs. Insert short spears into tubes at bottom of frame and tight- en lock bolts.

Frame Assembly

Long Spear

Short Spears

Eccentric Nut

5-7 TINE TEETH

Fasten tine teeth to bucket with fasteners provided as shown.

1/2 X 1-1/2” Bolt

3/8” U-Bolt

Tine Tooth

Lockwashers & Nuts

Page 28

Image 28

Bush Hog 2347 QT manual Fork Lift Option, Bale Spear Option, Tine Teeth

Contents

1207 $4.0050057986 OPERATION MAINTENANCECONGRATULATIONS TABLE OF CONTENTS RETAIL CUSTOMER’S RESPONSIBILITY UNDER THE BUSH HOG WARRANTYUNDERSTAND SIGNAL WORDS SECTION/PARATHIS LIMITED WARRANTY SHALL NOT APPLY DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGESLIMITED WARRANTY OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO2347 QT LOADER IT IS RECOMMENDED THAT TRACTOR BEEQUIPPED WITH ROLLOVER PROTECTIVE SYS TEM ROPS AND SEAT BELT BE USED FOR ALL LOADER OPERATIONSTHE TRACTOR IMPORTANT SAFETY PRECAUTIONSTHE LOADER SAFETY PRECAUTIONS CONTINUED OPERATING THE LOADEREMPLOYERS, EMPLOYEES AND OPERATIONS EMPLOYEE TRACTOR OPERATING INSTRUCTIONSIMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING This Act Seeks1-1 INTRODUCTION SECTION INTRODUCTION AND DESCRIPTION1-2 DESCRIPTION Table 1-1 TECHNICAL SPECIFICATIONS SERIES LOADERSECTION LOADER MOUNTING AND DISMOUNTING 2-1 PREPARING TRACTOR2-2 MOUNTING LOADER TO AVOID INJURY OR DEATHH. Tighten nut retaining cuff to 85 ft./lbs DO NOT STAND UNDER LOADER WHILE REMOVING/INSTALLING PARKING STANDSTighten Nut To 85 ft./lbs 2-3 DISMOUNTING LOADER DO NOT STAND UNDER LOADER WHILE REMOVING/INSTALLING PARKING STANDSSECTION OPERATING INSTRUCTIONS 3-1 GENERAL SAFETY3-2 OPERATION CAUTON DO NOT ATTEMPT TO LIFT BUCKET LOADS IN EXCESS OF CAPACITIES CAUTONLISTED IN TABLE 1-1 TECHNICAL SPECI FICATIONS CARRYING THE LOAD OPERATING WITH FLOAT CONTROL FLOATSidecutting is a good technique for cutting down a big pile FLOAT SURFACE MATERIAL LOADING FROM A BANKPEELING AND SCRAPING 6” 3RD CUT , 4TH CUT, ETCLOADING LOW TRUCKS OR SPREADERS FROM A PILE BACKFILLING3-3 BALE SPEAR OPERATION Handling large heavy objects can be extremely dangerous due toH Possibility of rolling the tractor over H Possibility of upending the tractor3-4 FORK LIFT OPERATION 3-5 QUICK HITCH OPERATION3-6 TRANSPORTING H TRANSPORT LOADS LOW AND SLOW H AVOID CONTACT WITH POWER LINESSECTION MAINTENANCE 4-1 MAINTENANCE CHECK LIST4-2 LUBRICATION Figure 4-3 HYDRAULIC SYSTEM PRESSURE REQUIREMENTS4-4 TROUBLESHOOTING TABLE 4-1 TROUBLESHOOTING PROCEDURESPROBLEM POSSIBLE CAUSEASSEMBLY 5-1 MAINFRAME ASSEMBLYSECTION THE FOLLOWING SAFETY PRECAUTIONSFigure 5-2 Parking Stands Installed Figure 5-4 Cuff Arrangement 5-2 OPTIONAL HYDRAULIC VALVE STAND ASSEMBLY Figure 5-3 OPTIONAL HYDRAULIC VALVE PLUMBING INSTRUCTIONS HOSE COLOR CODES5-4 BASIC POWER BEYOND PLUMBING INSTRUCTIONS 5-6 BALE SPEAR OPTION 5-5 FORK LIFT OPTION5-7 TINE TEETH SAFETY DECALS REAR VIEW OF SUBFRAME25H46071 79104 79103 24-6-423 25H46010TORQUE SPECIFICATIONS AMERICANMETRIC Bolt Head Markings