Manuals / Bush Hog / Lawn and Garden / Compact Loader

Bush Hog 2347 QT Safety Decals, Rear View Of Subframe, 25H46071 79104 79103 24-6-423, 25H46010

Models: 2347 QT

1 31

Page 29

SAFETY DECALS

To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damages can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge. Contact your authorized Bush Hog dealer for more information.

Decals 25H46070, 25H46071, 25H46010 and 25H46012 are located on the left side of Ô the subframe. Other decals are located on attachments (Bucket, Fork Lift, Bale Spear).

REAR VIEW OF

SUBFRAME

25H46071

79104

79103

24-6-423

62779


		25H46010
25H46070
25H46070	25H46012

Page 29

Image 29

Bush Hog 2347 QT manual Safety Decals, Rear View Of Subframe, 25H46071 79104 79103 24-6-423, 25H46010, 25H46070, 25H46012

Contents

$4.00 120750057986 OPERATION MAINTENANCECONGRATULATIONS RETAIL CUSTOMER’S RESPONSIBILITY UNDER THE BUSH HOG WARRANTY TABLE OF CONTENTSUNDERSTAND SIGNAL WORDS SECTION/PARADISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES THIS LIMITED WARRANTY SHALL NOT APPLYLIMITED WARRANTY OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOIT IS RECOMMENDED THAT TRACTOR BE 2347 QT LOADEREQUIPPED WITH ROLLOVER PROTECTIVE SYS TEM ROPS AND SEAT BELT BE USED FOR ALL LOADER OPERATIONSTHE LOADER IMPORTANT SAFETY PRECAUTIONSTHE TRACTOR OPERATING THE LOADER SAFETY PRECAUTIONS CONTINUEDEMPLOYEE TRACTOR OPERATING INSTRUCTIONS EMPLOYERS, EMPLOYEES AND OPERATIONSIMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING This Act Seeks1-2 DESCRIPTION SECTION INTRODUCTION AND DESCRIPTION1-1 INTRODUCTION SERIES LOADER Table 1-1 TECHNICAL SPECIFICATIONS2-1 PREPARING TRACTOR SECTION LOADER MOUNTING AND DISMOUNTING2-2 MOUNTING LOADER TO AVOID INJURY OR DEATHTighten Nut To 85 ft./lbs DO NOT STAND UNDER LOADER WHILE REMOVING/INSTALLING PARKING STANDSH. Tighten nut retaining cuff to 85 ft./lbs DO NOT STAND UNDER LOADER WHILE REMOVING/INSTALLING PARKING STANDS 2-3 DISMOUNTING LOADER3-2 OPERATION 3-1 GENERAL SAFETYSECTION OPERATING INSTRUCTIONS LISTED IN TABLE 1-1 TECHNICAL SPECI FICATIONS CAUTONCAUTON DO NOT ATTEMPT TO LIFT BUCKET LOADS IN EXCESS OF CAPACITIES CARRYING THE LOAD FLOAT OPERATING WITH FLOAT CONTROLSidecutting is a good technique for cutting down a big pile FLOAT SURFACE MATERIAL LOADING FROM A BANK3RD CUT , 4TH CUT, ETC PEELING AND SCRAPING 6”LOADING LOW TRUCKS OR SPREADERS FROM A PILE BACKFILLINGHandling large heavy objects can be extremely dangerous due to 3-3 BALE SPEAR OPERATIONH Possibility of rolling the tractor over H Possibility of upending the tractor3-5 QUICK HITCH OPERATION 3-4 FORK LIFT OPERATION3-6 TRANSPORTING H TRANSPORT LOADS LOW AND SLOW H AVOID CONTACT WITH POWER LINES4-1 MAINTENANCE CHECK LIST SECTION MAINTENANCE4-2 LUBRICATION Figure 4-3 HYDRAULIC SYSTEM PRESSURE REQUIREMENTSTABLE 4-1 TROUBLESHOOTING PROCEDURES 4-4 TROUBLESHOOTINGPROBLEM POSSIBLE CAUSE5-1 MAINFRAME ASSEMBLY ASSEMBLYSECTION THE FOLLOWING SAFETY PRECAUTIONSFigure 5-2 Parking Stands Installed Figure 5-4 Cuff Arrangement 5-2 OPTIONAL HYDRAULIC VALVE STAND ASSEMBLY Figure HOSE COLOR CODES 5-3 OPTIONAL HYDRAULIC VALVE PLUMBING INSTRUCTIONS5-4 BASIC POWER BEYOND PLUMBING INSTRUCTIONS 5-7 TINE TEETH 5-5 FORK LIFT OPTION5-6 BALE SPEAR OPTION REAR VIEW OF SUBFRAME SAFETY DECALS25H46071 79104 79103 24-6-423 25H46010AMERICAN TORQUE SPECIFICATIONSMETRIC Bolt Head Markings