Manuals / Bush Hog / Lawn and Garden / Compact Loader

Bush Hog 2347 QT manual Basic Power Beyond Plumbing Instructions

Models: 2347 QT

1 31

Download 31 pages 45.57 Kb

Page 27

Image 27

5-4 BASIC POWER BEYOND PLUMBING INSTRUCTIONS

IMPORTANT

When loader hydraulics are disconnected from tractor hydraulics, hoses A & B must be connected to complete tractor hydraulic circuit. FAILURE TO DO THIS WILL CAUSE SERIOUS DAMAGE TO TRACTOR HYDRAULIC SYSTEM.

Figure 5-7

Power Beyond

Plug

NOTE

More detailed assembly instructions are furnished with individual Power Beyond Kits.

Open Center

Plug

				Return		Inlet
	Pressurized			Return							Here)
									Hose		Here)
To							Long


			Inlet		(Use
		Sump	Inlet
	To	Sump						Pressure		Inlet
	To							Pressure
					To

These hoses to

be furnished by A dealer.

Page 27

Image 27

Bush Hog 2347 QT manual Basic Power Beyond Plumbing Instructions

Contents

OPERATION MAINTENANCE 1207$4.00 50057986CONGRATULATIONS SECTION/PARA TABLE OF CONTENTSRETAIL CUSTOMER’S RESPONSIBILITY UNDER THE BUSH HOG WARRANTY UNDERSTAND SIGNAL WORDSOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO THIS LIMITED WARRANTY SHALL NOT APPLYDISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES LIMITED WARRANTYTEM ROPS AND SEAT BELT BE USED FOR ALL LOADER OPERATIONS 2347 QT LOADERIT IS RECOMMENDED THAT TRACTOR BE EQUIPPED WITH ROLLOVER PROTECTIVE SYSIMPORTANT SAFETY PRECAUTIONS THE TRACTORTHE LOADER OPERATING THE LOADER SAFETY PRECAUTIONS CONTINUEDThis Act Seeks EMPLOYERS, EMPLOYEES AND OPERATIONSEMPLOYEE TRACTOR OPERATING INSTRUCTIONS IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNINGSECTION INTRODUCTION AND DESCRIPTION 1-1 INTRODUCTION1-2 DESCRIPTION SERIES LOADER Table 1-1 TECHNICAL SPECIFICATIONSTO AVOID INJURY OR DEATH SECTION LOADER MOUNTING AND DISMOUNTING2-1 PREPARING TRACTOR 2-2 MOUNTING LOADERDO NOT STAND UNDER LOADER WHILE REMOVING/INSTALLING PARKING STANDS H. Tighten nut retaining cuff to 85 ft./lbsTighten Nut To 85 ft./lbs DO NOT STAND UNDER LOADER WHILE REMOVING/INSTALLING PARKING STANDS 2-3 DISMOUNTING LOADER3-1 GENERAL SAFETY SECTION OPERATING INSTRUCTIONS3-2 OPERATION CAUTON CAUTON DO NOT ATTEMPT TO LIFT BUCKET LOADS IN EXCESS OF CAPACITIESLISTED IN TABLE 1-1 TECHNICAL SPECI FICATIONS CARRYING THE LOAD FLOAT SURFACE MATERIAL LOADING FROM A BANK OPERATING WITH FLOAT CONTROLFLOAT Sidecutting is a good technique for cutting down a big pileBACKFILLING PEELING AND SCRAPING 6”3RD CUT , 4TH CUT, ETC LOADING LOW TRUCKS OR SPREADERS FROM A PILEH Possibility of upending the tractor 3-3 BALE SPEAR OPERATIONHandling large heavy objects can be extremely dangerous due to H Possibility of rolling the tractor overH TRANSPORT LOADS LOW AND SLOW H AVOID CONTACT WITH POWER LINES 3-4 FORK LIFT OPERATION3-5 QUICK HITCH OPERATION 3-6 TRANSPORTING4-3 HYDRAULIC SYSTEM PRESSURE REQUIREMENTS SECTION MAINTENANCE4-1 MAINTENANCE CHECK LIST 4-2 LUBRICATION FigurePOSSIBLE CAUSE 4-4 TROUBLESHOOTINGTABLE 4-1 TROUBLESHOOTING PROCEDURES PROBLEMTHE FOLLOWING SAFETY PRECAUTIONS ASSEMBLY5-1 MAINFRAME ASSEMBLY SECTIONFigure 5-2 Parking Stands Installed Figure 5-4 Cuff Arrangement 5-2 OPTIONAL HYDRAULIC VALVE STAND ASSEMBLY Figure HOSE COLOR CODES 5-3 OPTIONAL HYDRAULIC VALVE PLUMBING INSTRUCTIONS5-4 BASIC POWER BEYOND PLUMBING INSTRUCTIONS 5-5 FORK LIFT OPTION 5-6 BALE SPEAR OPTION5-7 TINE TEETH 25H46010 SAFETY DECALSREAR VIEW OF SUBFRAME 25H46071 79104 79103 24-6-423Bolt Head Markings TORQUE SPECIFICATIONSAMERICAN METRIC