DIP Switch

SW1-SW4 for EDID/Audio

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DIP Switch Position

 

Video

 

 

Audio

 

 

Description

 

 

 

Pin#1

 

Pin#2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF [￿]

 

 

OFF [￿]

 

 

Up to

 

Stereo

1

 

 

Default Mode2 – Up to 1080p & stereo audio output for most

 

 

 

 

 

 

1080p

 

 

 

 

HDTVs

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF [￿]

 

 

ON [￿]

 

 

Up to 720p

 

Stereo

 

Safe Mode3 Enforce the system output at 720p/1080i video

 

 

 

 

 

 

/ 1080i

 

 

and stereo audio for basic compatibility among HDTVs

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ON [￿]

 

 

OFF [￿]

 

 

Bypass4

 

Bypass4

 

EDID Learning Mode5 – for learning EDID from the display

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

while playing any received HDMI audio format

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EDID Learning & Stereo Mode5 – for learning EDID from the

 

 

ON [￿]

 

 

ON [￿]

 

 

Bypass

 

Stereo

 

display while enforcing stereo output if any HDTV cannot play

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

surround sound normally

Note

1If the HDTV shows video but without audio, please try to set audio mode to stereo.

2Factory default of SW1-SW4: Pin#1-OFF [￿] & Pin#2- OFF [￿] for 1080p with stereo.

3If you encounter any unsolved audio/video output problem during system installation, please turn any SW1-SW4 to Pin#1-OFF[￿] & Pin#1-ON[￿], for safe mode to enforce the most compatible 720p stereo output for system check. However, the safe mode cannot be initiated if your HDMI source is set to enforce 1080p output. In this case, please reconfigure your HDMI source to all resolution output for troubleshooting.

4Bypass means the matrix will maintain playing the original format of HDMI signals in video and perhaps audio. By setting at this mode, the users may encounter compatibility issue among different kinds of HDMI sources and displays. If you cannot get the audio and/or video output normally at the system installation, please change the DIP switch setting to default mode or even safe mode to verify the functionality of the device.

5Set Pin#1 at ON[￿] first then connect the HDMI Input to HDTV through a HDMI cable. Wait for 20 seconds. The EDID learning procedure will be finished. If you want to learn the EDID from another HDTV, you must set Pin#1 at OFF[￿] first and repeat this procedure.

7

Page 8
Image 8
Cable Electronics HSW44C instruction manual DIP Switch Position Video Audio Description Pin#1 Pin#2 OFF