Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems 3T02-04 manual Related Manuals, Getting Help, anonymous, your email address

Models: 3T02-04

1 52

Download 52 pages 2.24 Kb

Page 11

Related Manuals

1.2 RELATED MANUALS

You may need to refer to the following documentation when you are using a Token Ring module:

•ATX User Guide – contains installation and conﬁguration instructions for the ATX.

•ATX MIB Reference Guide – contains Cabletron’s enterprise MIB.

If you need internetworking reference material, you may ﬁnd the following books helpful:

•Interconnections, Bridges and Routers, Radia Perlman, Addison Wesley  1992.

•Internetworking with TCP/IP: Protocols, and Architecture (2nd edition), Volumes I and II, Douglas Comer, Prentice Hall  1991.

•The Simple Book, An Introduction to Management of TCP/IP-based Internets, Marshall T. Rose, Prentice Hall  1991.

1.3 GETTING HELP

If you need additional support related to this device, or if you have any questions, comments, or suggestions concerning this manual, contact Cabletron Systems Technical Support:

By phone	(603) 332-9400
	Monday – Friday; 8 A.M. – 8 P.M. Eastern Time
By CompuServe	GO CTRON from any ! prompt
By Internet mail	support@ctron.com
By FTP	ctron.com (134.141.197.25)
Login	anonymous
Password	your email address

Token Ring Switch Module User Guide

Page 1-3

Image 11

Cabletron Systems 3T02-04 manual Related Manuals, Getting Help, anonymous, your email address

Contents

TOKEN RING SWITCH MODULE 3T02-04 AND 3T01-04 USER GUIDE Page Token Ring Switch Module User Guide VCCI NOTICE Token Ring Switch Module User GuideFCC NOTICE DOC NOTICECABLETRON SOFTWARE PROGRAM LICENSE EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITYToken Ring Switch Module User Guide CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENTUNITED STATES GOVERNMENT RESTRICTED RIGHTS Token Ring Switch Module User GuideToken Ring Switch Module User Guide CONTENTSCHAPTER 2 CONNECTING TO THE NETWORK CONFIGURINGToken Ring Switch Module User Guide ContentsCHAPTER 5 DIAGNOSTICS AND TROUBLESHOOTING TECHNICAL SPECIFICATIONSCHAPTER INTRODUCTION 1.1 DOCUMENT CONVENTIONS your email address 1.2 RELATED MANUALS1.3 GETTING HELP anonymous1.4 GENERAL DESCRIPTION Figure 1-2 3T02-04 and 3T01-04 Front Panels 1.6 CONNECTORS1.5 STANDARDS Figure 1-1 ATX Front PanelPage 1.7 LEDsToken Ring Switch Module User Guide Chapter 1 Introduction2.1 INTRODUCTION CHAPTER CONNECTING TO THE NETWORK2.2 POWER-UP LED SEQUENCE Chapter 2 Connecting to the Network 2.3 TYPICAL CONFIGURATIONS2.4 CONNECTING THE TOKEN RING MODULE TO A HUB 2.4.1 Unshielded Twisted Pair2.4.2 Shielded Twisted Pair Figure 2-2 Connecting a Token Ring Module to an STP MAU 3.1 INTRODUCTION CHAPTER CONFIGURING3.3 LCM COMMANDS 3.2 CONNECTING THE LCM3.5 CONFIGURING THE BRIDGING TYPE 3.5.1 Transparent 3.4 SETTING THE RING SPEED3.5.2.2 Segment Number 3.5.2 Source Routing and SRT3.5.2.1 Bridging Method 3.6 TRANSLATION OPTIONS 3.5.2.3 Bridge Number3.6.1 ARP Translation 3.6.3 IPX Translation 3.6.2 Source Routing ARP Translation3.6.4 AppleTalk Translation Off - perform no translation On - translate the packets Page Token Ring Switch Module User GuideChapter 3 Conﬁguring 4.1 DISPLAYING PORT STATUS CHAPTER STATISTICSDisabled - The port is not conﬁgured for Spanning Tree RXQ Overﬂows - number of incoming packets dropped by the port due to a lack of buffers. This entry shows status only it is not selectable. After a reboot, the ATX tries to automatically re-allocate the Small Buffers among the ports so that the total number of RXQ Overﬂows is minimized Forwarding Outcome 4.2 MODULE STATISTICSTable 4-1 Destination Addresses and Forwarding Outcomes Destination AddresssifTxSizes - The number of packets not sent due to size limitations Page Token Ring Switch Module User GuideChapter 4 Statistics 5.1 POWER-UP DIAGNOSTICS 5.1.1 Power-up Tests CHAPTER DIAGNOSTICS AND TROUBLESHOOTINGChapter 5 Diagnostics and Troubleshooting 5.1.2 Power-up Results5.2 OPERATIONAL DIAGNOSTICS 5.2.1 Loopback Tests 5.3 TROUBLESHOOTING 5.3.1 If the Module Fails to Power Up 5.2.2 Diagnostic Results5.3.2 Connectivity Problems CHAPTER ADDING/SWAPPING MODULES 6.1 UNPACKING THE TOKEN RING SWITCH MODULE6.2 ADDING A TOKEN RING SWITCH MODULE Delete all static addresses 6.3 SWAPPING A MODULE Page Token Ring Switch Module User GuideChapter 6 Adding/Swapping Modules APPENDIX A TECHNICAL SPECIFICATIONS DB9 for STP RJ45 for UTP B.1 OVERVIEW APPENDIX B BRIDGING METHODSAppendix B Bridging Methods B.2 TRANSPARENT BRIDGINGFigure B-1 Source Routing Example B.3 SOURCE ROUTING BRIDGINGStation C Figure B-2 Data Path Using Source Routing BridgingStation A B.4 SOURCE ROUTING TRANSPARENT BRIDGING Page B-6 Token Ring Switch Module User GuideAppendix B Bridging Methods INDEX Index-2 Token Ring Switch Module User GuideIndex