Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems 3T02-04 manual AppleTalk Translation

Models: 3T02-04

1 52

Download 52 pages 2.24 Kb

Page 26

3.6.4AppleTalk Translation

Chapter 3: Conﬁguring

NOTE

All Token Ring ports that have IPX translation enabled should always use the same option.

To enable the default option for port 5, enter:

ATX> translate 5 ipx on

To change the default to ethernet2, and change the IPX option to ethernet2 for ports 5 and 6.

ATX> translate 6 ipx ethernet2

To change the default to ethernet8022, and change the IPX option to ethernet8022 for ports 5, 6, and 7.

ATX> translate 7 ipx ethernet8022

3.6.4AppleTalk Translation

NOTE

AppleTalk Phase 1 does not exist on Token Ring and so is not a concern here. Also, since the ATX does not have physical LocalTalk connections, LocalTalk/LLAP is not a concern. Apple Macintoshes may be attached directly to standard LANs or may employ various LocalTalk-to-Ethernet routers to access LAN internetworks.

Page 3-8

Token Ring Switch Module User Guide

Image 26

Cabletron Systems 3T02-04 manual AppleTalk Translation

Contents

TOKEN RING SWITCH MODULE 3T02-04 AND 3T01-04 USER GUIDE Page Token Ring Switch Module User Guide DOC NOTICE Token Ring Switch Module User GuideFCC NOTICE VCCI NOTICECABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITYToken Ring Switch Module User Guide CABLETRON SOFTWARE PROGRAM LICENSEToken Ring Switch Module User Guide UNITED STATES GOVERNMENT RESTRICTED RIGHTSCONFIGURING CONTENTSCHAPTER 2 CONNECTING TO THE NETWORK Token Ring Switch Module User GuideTECHNICAL SPECIFICATIONS ContentsCHAPTER 5 DIAGNOSTICS AND TROUBLESHOOTING Token Ring Switch Module User GuideCHAPTER INTRODUCTION 1.1 DOCUMENT CONVENTIONS anonymous 1.2 RELATED MANUALS1.3 GETTING HELP your email address1.4 GENERAL DESCRIPTION Figure 1-1 ATX Front Panel 1.6 CONNECTORS1.5 STANDARDS Figure 1-2 3T02-04 and 3T01-04 Front PanelsChapter 1 Introduction 1.7 LEDsToken Ring Switch Module User Guide Page2.1 INTRODUCTION CHAPTER CONNECTING TO THE NETWORK2.2 POWER-UP LED SEQUENCE 2.4.1 Unshielded Twisted Pair 2.3 TYPICAL CONFIGURATIONS2.4 CONNECTING THE TOKEN RING MODULE TO A HUB Chapter 2 Connecting to the Network2.4.2 Shielded Twisted Pair Figure 2-2 Connecting a Token Ring Module to an STP MAU CHAPTER CONFIGURING 3.1 INTRODUCTION3.2 CONNECTING THE LCM 3.3 LCM COMMANDS3.4 SETTING THE RING SPEED 3.5 CONFIGURING THE BRIDGING TYPE 3.5.1 Transparent3.5.2.2 Segment Number 3.5.2 Source Routing and SRT3.5.2.1 Bridging Method 3.5.2.3 Bridge Number 3.6 TRANSLATION OPTIONS3.6.1 ARP Translation 3.6.2 Source Routing ARP Translation 3.6.3 IPX Translation3.6.4 AppleTalk Translation Off - perform no translation On - translate the packets Page Token Ring Switch Module User GuideChapter 3 Conﬁguring CHAPTER STATISTICS 4.1 DISPLAYING PORT STATUSDisabled - The port is not conﬁgured for Spanning Tree RXQ Overﬂows - number of incoming packets dropped by the port due to a lack of buffers. This entry shows status only it is not selectable. After a reboot, the ATX tries to automatically re-allocate the Small Buffers among the ports so that the total number of RXQ Overﬂows is minimized Destination Address 4.2 MODULE STATISTICSTable 4-1 Destination Addresses and Forwarding Outcomes Forwarding OutcomesifTxSizes - The number of packets not sent due to size limitations Page Token Ring Switch Module User GuideChapter 4 Statistics CHAPTER DIAGNOSTICS AND TROUBLESHOOTING 5.1 POWER-UP DIAGNOSTICS 5.1.1 Power-up TestsChapter 5 Diagnostics and Troubleshooting 5.1.2 Power-up Results5.2 OPERATIONAL DIAGNOSTICS 5.2.1 Loopback Tests 5.2.2 Diagnostic Results 5.3 TROUBLESHOOTING 5.3.1 If the Module Fails to Power Up5.3.2 Connectivity Problems CHAPTER ADDING/SWAPPING MODULES 6.1 UNPACKING THE TOKEN RING SWITCH MODULE6.2 ADDING A TOKEN RING SWITCH MODULE Delete all static addresses 6.3 SWAPPING A MODULE Page Token Ring Switch Module User GuideChapter 6 Adding/Swapping Modules APPENDIX A TECHNICAL SPECIFICATIONS DB9 for STP RJ45 for UTP APPENDIX B BRIDGING METHODS B.1 OVERVIEWB.2 TRANSPARENT BRIDGING Appendix B Bridging MethodsB.3 SOURCE ROUTING BRIDGING Figure B-1 Source Routing ExampleStation C Figure B-2 Data Path Using Source Routing BridgingStation A B.4 SOURCE ROUTING TRANSPARENT BRIDGING Page B-6 Token Ring Switch Module User GuideAppendix B Bridging Methods INDEX Index-2 Token Ring Switch Module User GuideIndex