Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems 3T02-04 manual 2 Connecting a Token Ring Module to an STP MAU

Models: 3T02-04

1 52

Download 52 pages 2.24 Kb

Page 18

Figure 2-2 Connecting a Token Ring Module to an STP MAU

Chapter 2: Connecting to the Network

To connect to an STP MAU, attach the DB9 end of a Token Ring adapter cable to the Token Ring module’s DB9 connector. Attach the Media Interface Connector (MIC), on the other end of the cable, to any port except the Ring-In or Ring-Out ports on a STP MAU. The Ring-In/ Ring-Out ports are used for interconnecting MAUs. Refer to the example shown in Figure 2-2.

				QUAD IEEE 802.5 TOKEN RING (STP)
	RING 1	RING 2	RING 3	RING 4
	RX ST	RX ST	RX ST	RX ST PROC
OFFLINE	TX 16	TX 16	TX 16	TX 16 PWR

RI

RO

Figure 2-2 Connecting a Token Ring Module to an STP MAU

Page 2-4

Token Ring Switch Module User Guide

Image 18

Cabletron Systems 3T02-04 manual 2 Connecting a Token Ring Module to an STP MAU

Contents

TOKEN RING SWITCH MODULE 3T02-04 AND 3T01-04 USER GUIDE Page Token Ring Switch Module User Guide DOC NOTICE Token Ring Switch Module User GuideFCC NOTICE VCCI NOTICECABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITYToken Ring Switch Module User Guide CABLETRON SOFTWARE PROGRAM LICENSEToken Ring Switch Module User Guide UNITED STATES GOVERNMENT RESTRICTED RIGHTSCONFIGURING CONTENTSCHAPTER 2 CONNECTING TO THE NETWORK Token Ring Switch Module User GuideTECHNICAL SPECIFICATIONS ContentsCHAPTER 5 DIAGNOSTICS AND TROUBLESHOOTING Token Ring Switch Module User GuideCHAPTER INTRODUCTION 1.1 DOCUMENT CONVENTIONS anonymous 1.2 RELATED MANUALS1.3 GETTING HELP your email address1.4 GENERAL DESCRIPTION Figure 1-1 ATX Front Panel 1.6 CONNECTORS1.5 STANDARDS Figure 1-2 3T02-04 and 3T01-04 Front PanelsChapter 1 Introduction 1.7 LEDsToken Ring Switch Module User Guide PageCHAPTER CONNECTING TO THE NETWORK 2.2 POWER-UP LED SEQUENCE2.1 INTRODUCTION 2.4.1 Unshielded Twisted Pair 2.3 TYPICAL CONFIGURATIONS2.4 CONNECTING THE TOKEN RING MODULE TO A HUB Chapter 2 Connecting to the Network2.4.2 Shielded Twisted Pair Figure 2-2 Connecting a Token Ring Module to an STP MAU CHAPTER CONFIGURING 3.1 INTRODUCTION3.2 CONNECTING THE LCM 3.3 LCM COMMANDS3.4 SETTING THE RING SPEED 3.5 CONFIGURING THE BRIDGING TYPE 3.5.1 Transparent3.5.2 Source Routing and SRT 3.5.2.1 Bridging Method3.5.2.2 Segment Number 3.5.2.3 Bridge Number 3.6 TRANSLATION OPTIONS3.6.1 ARP Translation 3.6.2 Source Routing ARP Translation 3.6.3 IPX Translation3.6.4 AppleTalk Translation Off - perform no translation On - translate the packets Token Ring Switch Module User Guide Chapter 3 ConﬁguringPage CHAPTER STATISTICS 4.1 DISPLAYING PORT STATUSDisabled - The port is not conﬁgured for Spanning Tree RXQ Overﬂows - number of incoming packets dropped by the port due to a lack of buffers. This entry shows status only it is not selectable. After a reboot, the ATX tries to automatically re-allocate the Small Buffers among the ports so that the total number of RXQ Overﬂows is minimized Destination Address 4.2 MODULE STATISTICSTable 4-1 Destination Addresses and Forwarding Outcomes Forwarding OutcomesifTxSizes - The number of packets not sent due to size limitations Token Ring Switch Module User Guide Chapter 4 StatisticsPage CHAPTER DIAGNOSTICS AND TROUBLESHOOTING 5.1 POWER-UP DIAGNOSTICS 5.1.1 Power-up Tests5.1.2 Power-up Results 5.2 OPERATIONAL DIAGNOSTICS 5.2.1 Loopback TestsChapter 5 Diagnostics and Troubleshooting 5.2.2 Diagnostic Results 5.3 TROUBLESHOOTING 5.3.1 If the Module Fails to Power Up5.3.2 Connectivity Problems 6.1 UNPACKING THE TOKEN RING SWITCH MODULE 6.2 ADDING A TOKEN RING SWITCH MODULECHAPTER ADDING/SWAPPING MODULES Delete all static addresses 6.3 SWAPPING A MODULE Token Ring Switch Module User Guide Chapter 6 Adding/Swapping ModulesPage APPENDIX A TECHNICAL SPECIFICATIONS DB9 for STP RJ45 for UTP APPENDIX B BRIDGING METHODS B.1 OVERVIEWB.2 TRANSPARENT BRIDGING Appendix B Bridging MethodsB.3 SOURCE ROUTING BRIDGING Figure B-1 Source Routing ExampleFigure B-2 Data Path Using Source Routing Bridging Station AStation C B.4 SOURCE ROUTING TRANSPARENT BRIDGING Token Ring Switch Module User Guide Appendix B Bridging MethodsPage B-6 INDEX Token Ring Switch Module User Guide IndexIndex-2