Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems 3T02-04 manual Delete all static addresses

Models: 3T02-04

1 52

Download 52 pages 2.24 Kb

Page 40

Chapter 6: Adding/Swapping Modules

If the module you are adding has a different number of ports than the module you are removing, before you can power cycle the ATX you must:

•Delete all static addresses

•Delete all ARP addresses and IP routing table entries

•Delete all ﬁlters

1.Make sure the ATX is powered off.

2.Remove the network connections from the module you are going to replace.

3.Loosen the screws at each end of the front panel of the interface module you are going to replace.

4.Remove the installed interface module by pulling gently but firmly on the ears at the ends of the module's front panel.

5.Gently slide the new module into the plastic guides in the module slot until it is completely inserted. Push the module firmly into place, as far as it will go, to fully engage the connectors at the back of the module with the backplane at the rear of the ATX chassis.

6.Tighten the screws on each side of the Token Ring module front panel.

7.Power on the ATX, and check the module LED power-on sequence as described in Chapter 2, Connecting to the Network.

8.Make the connections to the network as described in Chapter 2.

Page 6-2

Token Ring Switch Module User Guide

Image 40

Cabletron Systems 3T02-04 manual Delete all static addresses

Contents

TOKEN RING SWITCH MODULE 3T02-04 AND 3T01-04 USER GUIDE Page Token Ring Switch Module User Guide Token Ring Switch Module User Guide FCC NOTICEDOC NOTICE VCCI NOTICEEXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY Token Ring Switch Module User GuideCABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT CABLETRON SOFTWARE PROGRAM LICENSEToken Ring Switch Module User Guide UNITED STATES GOVERNMENT RESTRICTED RIGHTSCONTENTS CHAPTER 2 CONNECTING TO THE NETWORKCONFIGURING Token Ring Switch Module User GuideContents CHAPTER 5 DIAGNOSTICS AND TROUBLESHOOTINGTECHNICAL SPECIFICATIONS Token Ring Switch Module User GuideCHAPTER INTRODUCTION 1.1 DOCUMENT CONVENTIONS 1.2 RELATED MANUALS 1.3 GETTING HELPanonymous your email address1.4 GENERAL DESCRIPTION 1.6 CONNECTORS 1.5 STANDARDSFigure 1-1 ATX Front Panel Figure 1-2 3T02-04 and 3T01-04 Front Panels1.7 LEDs Token Ring Switch Module User GuideChapter 1 Introduction Page2.2 POWER-UP LED SEQUENCE CHAPTER CONNECTING TO THE NETWORK2.1 INTRODUCTION 2.3 TYPICAL CONFIGURATIONS 2.4 CONNECTING THE TOKEN RING MODULE TO A HUB2.4.1 Unshielded Twisted Pair Chapter 2 Connecting to the Network2.4.2 Shielded Twisted Pair Figure 2-2 Connecting a Token Ring Module to an STP MAU CHAPTER CONFIGURING 3.1 INTRODUCTION3.2 CONNECTING THE LCM 3.3 LCM COMMANDS3.4 SETTING THE RING SPEED 3.5 CONFIGURING THE BRIDGING TYPE 3.5.1 Transparent3.5.2.1 Bridging Method 3.5.2 Source Routing and SRT3.5.2.2 Segment Number 3.5.2.3 Bridge Number 3.6 TRANSLATION OPTIONS3.6.1 ARP Translation 3.6.2 Source Routing ARP Translation 3.6.3 IPX Translation3.6.4 AppleTalk Translation Off - perform no translation On - translate the packets Chapter 3 Conﬁguring Token Ring Switch Module User GuidePage CHAPTER STATISTICS 4.1 DISPLAYING PORT STATUSDisabled - The port is not conﬁgured for Spanning Tree RXQ Overﬂows - number of incoming packets dropped by the port due to a lack of buffers. This entry shows status only it is not selectable. After a reboot, the ATX tries to automatically re-allocate the Small Buffers among the ports so that the total number of RXQ Overﬂows is minimized 4.2 MODULE STATISTICS Table 4-1 Destination Addresses and Forwarding OutcomesDestination Address Forwarding OutcomesifTxSizes - The number of packets not sent due to size limitations Chapter 4 Statistics Token Ring Switch Module User GuidePage CHAPTER DIAGNOSTICS AND TROUBLESHOOTING 5.1 POWER-UP DIAGNOSTICS 5.1.1 Power-up Tests5.2 OPERATIONAL DIAGNOSTICS 5.2.1 Loopback Tests 5.1.2 Power-up ResultsChapter 5 Diagnostics and Troubleshooting 5.2.2 Diagnostic Results 5.3 TROUBLESHOOTING 5.3.1 If the Module Fails to Power Up5.3.2 Connectivity Problems 6.2 ADDING A TOKEN RING SWITCH MODULE 6.1 UNPACKING THE TOKEN RING SWITCH MODULECHAPTER ADDING/SWAPPING MODULES Delete all static addresses 6.3 SWAPPING A MODULE Chapter 6 Adding/Swapping Modules Token Ring Switch Module User GuidePage APPENDIX A TECHNICAL SPECIFICATIONS DB9 for STP RJ45 for UTP APPENDIX B BRIDGING METHODS B.1 OVERVIEWB.2 TRANSPARENT BRIDGING Appendix B Bridging MethodsB.3 SOURCE ROUTING BRIDGING Figure B-1 Source Routing ExampleStation A Figure B-2 Data Path Using Source Routing BridgingStation C B.4 SOURCE ROUTING TRANSPARENT BRIDGING Appendix B Bridging Methods Token Ring Switch Module User GuidePage B-6 INDEX Index Token Ring Switch Module User GuideIndex-2