Manuals / Brands / Computer Equipment / Switch / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems 6E122-26, 6E123-26, 6E132-25, 6E133-25 A.5 COM PORT PINOUT ASSIGNMENTS, A.6 REGULATORY COMPLIANCE

1 184

Download 184 pages, 1.33 Mb

COM Port Pinout Assignments

6E122-26, 6E132-25, 6E123-26 and 6E133-25 User’s Guide A-3

A.5 COM PORT PINOUT ASSIGNMENTS

The COM port is a serial communications port that supports Local

Management or connection to a UPS.

The COM port has the following pin assignments:

A.6 REGULATORY COMPLIANCE

Safety

The 6E12X-26 and 6E13X-25 meet the safety requirements of UL 1950,

CSA C22.2 No. 950, EN 60950, IEC 950 and 73/23/EEC.

Electromagnetic Compatibility (EMC)

The 6E12X-26 and 6E13X-25 meet the requirements of FCC Part 15,

EN 50082-1, EN 55022, VCCI V-3, CSA C108.8, AS/NZS 3548, and

89/336/EEC.

Table A-1 COM Port Pin Assignments

Pin Signal Name Input/Output

1 Transmit Data (XMT) Output

2 Data Carrier Detect (DCD) Output

3 Data Set Ready (DSR) Input

4 Receive Data (RCV) Input

5 Signal Ground (GND) NA

6 Data Terminal Ready (DTR) Output

7 Request to Send (RTS) Input

8 Clear to Send (CTS) NA

Contents

Main 9032076-05 6E122-26 6E132-25 6E133-25 6E123-26 Page 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide i FCC NOTICE NOTICE ii 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide iii UNITED STATES GOVERNMENT RESTRICTED RIGHTS EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY CABLETRON SOFTWARE PROGRAM LICENSE iv 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide DECLARATION OF CONFORMITY 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide v CONTENTS vi 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide vii viii 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide Page Page CHAPTER 1 INTRODUCTION 1.2 STRUCTURE OF THIS GUIDE 1.1 USING THIS GUIDE 1.3 6E12X-26 AND 6E13X-25 OVERVIEW 6E12X-26 and 6E13X-25 Overview Figure 1-1 The 6E122-26 and 6E132-25 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide 1-3 1.3.1 Connectivity 1.3.2 Full Duplex Switched Ethernet 1.3.3 SmartTrunk 1.3.5 Switching Options 1.3.4 Management 1.3.6 Standards Compatibility 1.3.9 Runtime IP Address Discovery 1.3.8 Year 2000 Compliant 1.3.7 LANVIEW Diagnostic LEDs 1.3.10 Local Management Features 1.4 OPTIONAL FEATURES Document Conventions 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide 1-9 1.5 DOCUMENT CONVENTIONS The following conventions are used throughout this document: 1.6 GETTING HELP 1.7 RELATED MANUALS Page CHAPTER 2 NETWORK REQUIREMENTS 2.1 SmartTrunk 2.2 10BASE-T NETWORK 2.3 100BASE-TX NETWORK 2.4 100BASE-FX FIBER OPTIC NETWORK CHAPTER 3 INSTALLATION 3.1 REQUIRED TOOLS 3.2 UNPACKING THE 6E12X-26 AND 6E13X-25 3.3 6E12X-26 AND 6E13X-25 OPTIONS 3.4 INSTALLING THE 6E12X-26 AND 6E13X-25 INTO THE 6C105 CHASSIS Page Chapter 3: Installation Figure 3-1 Installing an Interface Module 3-4 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide 3.5 CONNECTING TO THE NETWORK 3.5.1 Connecting UTP Cables to Ports 1 Through 24 of the 6E122-26 and 6E132-25 Page 3.5.2 Connecting UTP Cables to Ports 1 Through 24 of the 6E133-25 and 6E123-26 Page 3.5.3 Connecting a Twisted Pair Segment to the FE-100TX Page 3.5.4 Connecting a Fiber Optic Segment to the FE-100FX and FE-100F3 Page 3.6 COMPLETING THE INSTALLATION CHAPTER 4 TROUBLESHOOTING 4.1 USING LANVIEW Chapter 4: Troubleshooting 6E122-26 207604 Figure 4-1 LANVIEW LEDs 4-2 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide Using LANVIEW 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide 4-3 4.2 FE-100TX LED FE-100TX LED 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide 4-5 LED is on. (RX) LED is off. Chapter 4: Troubleshooting 4.3 TROUBLESHOOTING CHECKLIST 4.4 USING THE RESET BUTTON 6E132-25 Page CHAPTER 5 LOCAL MANAGEMENT 5.1 OVERVIEW 5-2 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide 5.2 LOCAL MANAGEMENT KEYBOARD CONVENTIONS 5.3 MANAGEMENT TERMINAL SETUP 5.3.1 Console Cable Connection 5.3.2 Connecting an Uninterruptible Power Supply (UPS) Management Terminal Setup 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide 5-5 5.3.3 Management Terminal Setup Parameters Table 5-2 lists the setup parameters for the local management terminal. 5.3.4 Telnet Connections 5.4 ACCESSING LOCAL MANAGEMENT 5.4.1 Navigating Local Management Screens Accessing Local Management 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide 5-9 Figure 5-4 802.1D Switching Mode, LM Screen Hierarchy Figure 5-5 802.1Q Switching Mode, LM Screen Hierarchy 5-10 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide 5.4.2 Selecting Local Management Menu Screen Items 5.4.3 Exiting Local Management Screens There are two ways to exit Local Management (LM). Using the EXIT Command Page 5.5 THE MAIN MENU SCREEN 5.6 CHASSIS MENU SCREEN Page 5.7 CHASSIS CONFIGURATION SCREEN Page 5.7.1 Setting the IP Address 5.7.2 Setting the Subnet Mask 5.7.3 Setting the Chassis Date 5.7.4 Setting the Chassis Time 5.7.5 Entering a New Screen Refresh Time 5.7.6 Setting the Screen Lockout Time 5.7.7 Setting the Operational Mode Page 5.8 SNMP COMMUNITY NAMES SCREEN 5.8.1 Establishing Community Names Page 5.9 SNMP TRAPS SCREEN 5.9.1 Conguring the Trap Table 5.10 CHASSIS ENVIRONMENTAL SCREEN 5.11 PORT REDIRECT FUNCTION SCREEN Port Redirect Function Screen 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide 5-31 Figure 5-14 Port Redirect Function Screen Source Module [ The following denitions briey explain each eld of the Port Redirect Function screen. Source Module (Read-Only) Allows a selected module [n] to be congured as a source module. Displays which modules are currently set as source modules. Source Port (Read-Only) 5.11.1 Displaying the Source and Destination Entries 5.11.2 Changing Source and Destination Ports 5.12 MODULE SELECTION SCREEN 5.12.1 Selecting a Module 5-36 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide 5.13 MODULE MENU SCREEN Page 5.14 MODULE CONFIGURATION MENU SCREEN Module Conguration Menu Screen Figure 5-17 Module Conguration Menu Screen 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide 5-39 Page 5.15 GENERAL CONFIGURATION SCREEN Page Page Page 5.15.1 Setting the IP Address 5.15.2 Setting the Subnet Mask 5.15.3 Setting the Default Gateway 5.15.4 Setting the TFTP Gateway IP Address 5.15.5 Setting the Module Date 5.15.6 Setting the Module Time 5.15.7 Entering a New Screen Refresh Time 5.15.8 Setting the Screen Lockout Time 5.15.9 Setting the Operational Mode 5.15.10 Setting the Management Mode 5.15.11 Conguring the COM Port WARNING 5.15.12 Changing the Com Port Application 5.15.13 Clearing NVRAM WARNING 5.15.14 Enabling/Disabling IP Fragmentation 5.16 SNMP COMMUNITY NAMES SCREEN Page 5.16.1 Establishing Community Names 5-60 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide 5.17 SNMP TRAPS SCREEN Figure 5-23 SNMP Traps Screen The following explains each eld of the SNMP Traps screen. Trap Destination (Modiable) NOTE It is only necessary to assign SNMP traps if the user desires 5.17.1 Conguring the Trap Table 5.18 SWITCH CONFIGURATION SCREEN Switch Conguration Screen 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide 5-63 Figure 5-24 Switch Conguration Screen The following describe each eld of the Switch Conguration screen: Switch Address (Read-Only) Displays the base MAC address of the switch. Number of Ports (Read-Only) Displays the total number of switched ports on the module. 5.18.1 Setting the STA 5.18.2 Setting the Age Time 5.18.3 Setting (Enabling or Disabling) the Port Status 5-66 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide 5.19 ETHERNET FULL DUPLEX CONFIGURATION SCREEN Figure 5-25 Ethernet Full Duplex Conguration Screen Page 5.19.1 Setting the Operation Mode 5.20 MODULE SPECIFIC CONFIGURATION MENU SCREEN Page Page 5.21 SYSTEM RESOURCES SCREEN 5.21.1 Setting the Reset Peak Utilization 5.22 HIGH SPEED INTERFACE CONFIGURATION MENU SCREEN (6E12X-26 ONLY) Page Page 5.22.1 Conguring an FE-100FX or FE-100F3 in Port 25 or 26 5.22.2 Setting the FE-100FX and FE-100F3 Operational Mode 5.22.3 Conguring an FE-100TX in Port 25 or 26 5.22.4 Setting the FE-100TX Operational Mode 5.22.5 Setting the FE-100TX Advertised Ability 5.23 FLASH DOWNLOAD SCREEN Page Page 5.23.1 Image File Download Using TFTP 5.23.2 Image File Download Using RUNTIME 5.23.3 Image File Download Using BootP 5.24 PORT REDIRECT FUNCTION SCREEN 5-86 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide Figure 5-30 Port Redirect Function Screen Destination Port [ Source Port [ The following denitions briey explain each eld of the Port Redirect Function screen: Source Port (Read-only) Allows a selected port [n] to be changed to a destination port. Shows which ports are currently set as source ports. Destination Port (Read-only) 5.24.1 Displaying the Source and Destination Entries 5.24.2 Changing Source and Destination Ports Page Broadcast Suppression Screen 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide 5-89 5.25 BROADCAST SUPPRESSION SCREEN Figure 5-31 Broadcast Suppression Screen NOTE The Broadcast Suppression screen may not be available if the 5.25.1 Setting the Threshold 5.25.2 Setting the Reset Peak Switch 5.26 MODULE STATISTICS MENU SCREEN Page Switch Statistics Screen 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide 5-93 5.27 SWITCH STATISTICS SCREEN Identies the interface or port number. Figure 5-33 Switch Statistics Screen The Switch Statistics screen displays the following menu items: Interface # (Read-Only) 5.27.1 Using the Clear Counters Command The Interface Statistics Screen 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide 5-95 5.28 THE INTERFACE STATISTICS SCREEN X Figure 5-34 Interface Statistics Screen NOTE Cabletron Systems HSIMs gather their own statistics, and may Page Page 5.28.1 Displaying Interface Statistics RMON Statistics Screen 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide 5-99 5.28.2 Using the Clear Counters Command 5.29 RMON STATISTICS SCREEN Figure 5-35 RMON Statistics Screen NOTE The RMON Statistics screen provides statistics for all front Page Page Page 5.29.1 Displaying RMON Statistics 5.29.2 Using the Clear Counters Command 5.30 NETWORK TOOLS 5.30.1 Built-in Commands Page Page Page Page Page Page Page Page Page 5.30.2 Special Commands Page APPENDIX A SPECIFICATIONS A.1 DEVICE SPECIFICATIONS A.3 ENVIRONMENTAL REQUIREMENTS A.2 PHYSICAL PROPERTIES A.4 INPUT/OUTPUT PORTS A.5 COM PORT PINOUT ASSIGNMENTS A.6 REGULATORY COMPLIANCE Page APPENDIX B FE-100TX, FE-100FX AND FE-100F3 SPECIFICATIONS B.1 FE-100TX Appendix B: FE-100TX, FE-100FX and FE-100F3 Specications B-2 6E128-26, 6E138-25, 6E129-26 and 6E139-25 Users Guide B.2 FE-100FX FE-100F3 6E128-26, 6E138-25, 6E129-26 and 6E139-25 Users Guide B-3 B.3 FE-100F3 Page APPENDIX C MODE SWITCH BANK SETTINGS AND OPTIONAL INSTALLATIONS C.1 REQUIRED TOOLS C.2 SETTING THE MODE SWITCH Page Page Appendix C: Mode Switch Bank Settings and Optional Installations C-4 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide C.3 INSTALLING OPTIONAL FAST ETHERNET INTERFACE MODULES Page Page Page Page INDEX 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide Index-1 Numerics A B H I K L M O P R S Index-4 6E122-26, 6E132-25, 6E123-26 and 6E133-25 Users Guide T U