FEPIM Speciﬁcations, FE-100TX | Cabletron Systems TRFMIM-28 specs

Appendix A

Appendix A

FEPIM Speciﬁcations

The 9H423-28 SmartSwitch 9000 module uses a Fast Ethernet Interface Module (FEPIM) to provide front panel cable connections. FEPIMs are user-installable. See the section titled Installing an FEPIM in Chapter 2.

FE-100TX

The FE-100TX is an RJ45 connector supporting Unshielded Twisted Pair (UTP) cabling.

The slide switch on the FE-100TX determines the crossover status of the cable pairs. If the switch is on the X side, the pairs are internally crossed over. If the switch is on the = side, the pairs are not internally crossed over. Figure A-1 shows the pinouts for the FEPIM-100TX in both positions.

Position =

(not crossed over)

1. TX+ 5. NC

2. TX- 6. RX-

3.RX+ 7. NC

4.NC 8. NC

=

x

10

100

FE-100TX

166505

Position X (crossed over)

1.RX+ 5. NC

2.RX- 6. TX-

3.TX+ 7. NC

4.NC 8. NC

Figure A-1. FE-100TX Pinouts

FE-100FX

The FE-100FX shown in Figure A-2 supports multimode ﬁber optic cabling. The FE-100FX is equipped with an SC-style port. Table A-1 lists the speciﬁcations for the FE-100FX.

A-1

Image 43

Cabletron Systems TRFMIM-28 manual FEPIM Speciﬁcations, FE-100TX, FE-100FX, Appendix A

Contents

9032061-01 SmartSwitch 9H423-28 User’s GuidePage Copyright March 1998 by Cabletron Systems, Inc 35 Industrial Way VCCI Notice FCC NoticeDOC Notice Nexus House, Newbury Business Park DECLARATION OF CONFORMITY ADDENDUMConformance to Directives/Product Standards CLASS 1 LASER TRANSCEIVERS Safety InformationThe FPIM-05 and FPIM-07 are Class 1 Laser Products CLASS 1 LASER TRANSCEIVERS Laser Radiation and Connectors Page Introduction ContentsInstalling the 9H423-28 Module Chapter Contents Speciﬁcationsviii Chapter Introduction Management FeaturesFast Packet Switching Processor The 9H423-28 module provides MIB support including RMON RFC-1271 LANVIEW LEDs SMB CPU INB FAST ENET Figure 1-1. The 9H423-28 Module26X 25X FAST ENET 9H423-28 Getting Help Related Manuals Installing an FEPIM Installing the 9H423-28 ModuleUnpacking the Module User Accessible Components Setting the Module DIP Switch See the Cautions at the end of this table Table 2-1. Function of DIP Switch Installing the Module in the SmartSwitch 9000 Chassis Module Figure 2-3. Installing the ModulePlastic Tab Jack for ESD Wrist Strap Metal Back-Panel Reset Switch The Reset Switch Installing the 9H423-28 Module Operation Operation ENIB/FENIB Traditional Switch SmartSwitch ASICVLAN VLAN Domains Fully-Meshed VLAN Domains SecureFast VLAN Switches SMB-1 Bus i960 CoreINB NIB System Management Buses SMB-10 Bus System Diagnostic ControllerDC/DC Converter INB Interface Lowest Slot Number Level ITDM Arbitration LevelsITDM RAM Allocation Level Round Robin Arbitration Level Monarch/Slave SmartSwitch 9000 Modules 3-10 System Status INB Transmit Port Receive LANVIEW LEDsINB Receive Port Transmit The function of the INB Transmit LEDs is listed in Table The function of the INB Receive LEDs is listed in TableLANVIEW LEDs Table 4-5. Port Transmit LEDs The function of the Port Receive LEDs is listed in TableThe function of the Port Transmit LEDs is listed in Table Table 4-4. Port Receive LEDs LANVIEW LEDs Standards SpeciﬁcationsTechnical Speciﬁcations Memory Weight SafetyService Dimensions Storage Temperature EnvironmentOperating Temperature 5 to 40 C Speciﬁcations Appendix A FEPIM SpeciﬁcationsFE-100TX FE-100FX FEPIM Speciﬁcations FE-100FX