Installing the 9H423-28 Module | Cabletron Systems TRFMIM-28

Installing the 9H423-28 Module

Chapter 2

Installing the 9H423-28 Module

The 9H423-28 module occupies a single slot in the SmartSwitch 9000 chassis.

NOTE

The INB Terminator Modules must be installed on the rear of the chassis before powering up this module. Refer to the INB Terminator Modules Installation Guide for information and installation procedure.

Install the modules by following the steps starting below.

Unpacking the Module

1.Carefully remove the module from the shipping box. (Save the box and packing materials in the event the module must be reshipped.)

2.Remove the module from the plastic bag. Observe all precautions to prevent damage from Electrostatic Discharge (ESD).

3.Carefully examine the module, checking for damage. If any damage exists, DO NOT install the module. Contact Cabletron Systems Technical Support immediately.

Installing an FEPIM

The 9H423-28 provides a slot for a Cabletron FEPIM (Fast Ethernet Port Interface Module). The 9H423-28 SmartSwitch module is shipped without FEPIMs. To install an FEPIM, follow the procedure below:

1.Remove the module if it is installed in the SmartSwitch 9000 chassis.

2.Remove the two screws securing the plate on the side of the FEPIM slot.

2-1

Image 17

Cabletron Systems TRFMIM-28 manual Installing the 9H423-28 Module, Unpacking the Module, Installing an FEPIM, Chapter

Contents

9032061-01 SmartSwitch 9H423-28 User’s GuidePage Copyright March 1998 by Cabletron Systems, Inc 35 Industrial Way DOC Notice FCC NoticeVCCI Notice Conformance to Directives/Product Standards DECLARATION OF CONFORMITY ADDENDUMNexus House, Newbury Business Park The FPIM-05 and FPIM-07 are Class 1 Laser Products Safety InformationCLASS 1 LASER TRANSCEIVERS CLASS 1 LASER TRANSCEIVERS Laser Radiation and Connectors Page Installing the 9H423-28 Module ContentsChapter Introduction viii SpeciﬁcationsContents Chapter Introduction Fast Packet Switching FeaturesProcessor Management The 9H423-28 module provides MIB support including RMON RFC-1271 LANVIEW LEDs 26X 25X Figure 1-1. The 9H423-28 ModuleFAST ENET 9H423-28 SMB CPU INB FAST ENET Getting Help Related Manuals Unpacking the Module Installing the 9H423-28 ModuleInstalling an FEPIM User Accessible Components Setting the Module DIP Switch See the Cautions at the end of this table Table 2-1. Function of DIP Switch Installing the Module in the SmartSwitch 9000 Chassis Plastic Tab Jack for ESD Wrist Strap Figure 2-3. Installing the ModuleMetal Back-Panel Module Reset Switch The Reset Switch Installing the 9H423-28 Module Operation Operation ENIB/FENIB VLAN SmartSwitch ASICTraditional Switch VLAN Domains Fully-Meshed VLAN Domains SecureFast VLAN Switches INB NIB i960 CoreSystem Management Buses SMB-1 Bus DC/DC Converter System Diagnostic ControllerINB Interface SMB-10 Bus ITDM RAM Allocation Level ITDM Arbitration LevelsRound Robin Arbitration Level Lowest Slot Number Level Monarch/Slave SmartSwitch 9000 Modules 3-10 INB Receive LANVIEW LEDsPort Transmit System Status INB Transmit Port Receive LANVIEW LEDs The function of the INB Receive LEDs is listed in TableThe function of the INB Transmit LEDs is listed in Table The function of the Port Transmit LEDs is listed in Table The function of the Port Receive LEDs is listed in TableTable 4-4. Port Receive LEDs Table 4-5. Port Transmit LEDs LANVIEW LEDs Technical Speciﬁcations SpeciﬁcationsMemory Standards Service SafetyDimensions Weight Operating Temperature Environment5 to 40 C Storage Temperature Speciﬁcations FE-100TX FEPIM SpeciﬁcationsFE-100FX Appendix A FEPIM Speciﬁcations FE-100FX