Safety Information | Cabletron Systems TRFMIM-28 instruction

Safety Information

Notice

Safety Information

CLASS 1 LASER TRANSCEIVERS

The FPIM-05 and FPIM-07 are Class 1 Laser Products

CLASS 1

LASER PRODUCT

The FPIM-05 and FPIM-07 use Class 1 Laser transceivers. Read the following safety information before installing or operating these adapters.

The Class 1 laser transceivers use an optical feedback loop to maintain Class 1 operation limits. This control loop eliminates the need for maintenance checks or adjustments. The output is factory set, and does not allow any user adjustment. Class 1 Laser transceivers comply with the following safety standards:

•21 CFR 1040.10 and 1040.11 U.S. Department of Health and Human Services (FDA).

•IEC Publication 825 (International Electrotechnical Commission).

•CENELEC EN 60825 (European Committee for Electrotechnical Standardization).

When operating within their performance limitations, laser transceiver output meets the Class 1 accessible emission limit of all three standards. Class 1 levels of laser radiation are not considered hazardous.

iv

Image 6

Cabletron Systems TRFMIM-28 manual Safety Information, CLASS 1 LASER TRANSCEIVERS

Contents

SmartSwitch 9H423-28 User’s Guide 9032061-01Page Copyright March 1998 by Cabletron Systems, Inc 35 Industrial Way FCC Notice VCCI NoticeDOC Notice DECLARATION OF CONFORMITY ADDENDUM Nexus House, Newbury Business ParkConformance to Directives/Product Standards Safety Information CLASS 1 LASER TRANSCEIVERSThe FPIM-05 and FPIM-07 are Class 1 Laser Products CLASS 1 LASER TRANSCEIVERS Laser Radiation and Connectors Page Chapter ContentsInstalling the 9H423-28 Module Introduction Speciﬁcations Contentsviii Introduction Chapter Processor FeaturesFast Packet Switching Management The 9H423-28 module provides MIB support including RMON RFC-1271 LANVIEW LEDs FAST ENET 9H423-28 Figure 1-1. The 9H423-28 Module26X 25X SMB CPU INB FAST ENET Related Manuals Getting Help Installing the 9H423-28 Module Installing an FEPIMUnpacking the Module User Accessible Components Setting the Module DIP Switch Table 2-1. Function of DIP Switch See the Cautions at the end of this table Installing the Module in the SmartSwitch 9000 Chassis Metal Back-Panel Figure 2-3. Installing the ModulePlastic Tab Jack for ESD Wrist Strap Module The Reset Switch Reset Switch Installing the 9H423-28 Module Operation ENIB/FENIB Operation SmartSwitch ASIC Traditional SwitchVLAN VLAN Domains SecureFast VLAN Switches Fully-Meshed VLAN Domains System Management Buses i960 CoreINB NIB SMB-1 Bus INB Interface System Diagnostic ControllerDC/DC Converter SMB-10 Bus Round Robin Arbitration Level ITDM Arbitration LevelsITDM RAM Allocation Level Lowest Slot Number Level Monarch/Slave SmartSwitch 9000 Modules 3-10 Port Transmit LANVIEW LEDsINB Receive System Status INB Transmit Port Receive The function of the INB Receive LEDs is listed in Table The function of the INB Transmit LEDs is listed in TableLANVIEW LEDs Table 4-4. Port Receive LEDs The function of the Port Receive LEDs is listed in TableThe function of the Port Transmit LEDs is listed in Table Table 4-5. Port Transmit LEDs LANVIEW LEDs Memory SpeciﬁcationsTechnical Speciﬁcations Standards Dimensions SafetyService Weight 5 to 40 C EnvironmentOperating Temperature Storage Temperature Speciﬁcations FE-100FX FEPIM SpeciﬁcationsFE-100TX Appendix A FE-100FX FEPIM Speciﬁcations