Cambridge Audio 540D V2 user manual Rear panel connections

azur 540D V2

Rear panel connections

Power Off

6

7

9

On

Video Out

Class 1 Laser Product

2

3

4

5

5.1 Channel Audio Out

Stereo

Designed in London, England

Composite

Luokan 1 Laserplaite

Y

Klass 1 Laserapparat

Out

azur 540D V2.0 DVD Player

1

Power AC

Control Bus

IR Emitter

Digital Outputs

C

SL

L

L

Power Rating: 100-240V AC ~ 50/60Hz

Toslink

S/P DIF

Max Power Consumption: 25W

In

Optical

Co-axial

www.cambridge-audio.com

Cb/Pb

Caution

Risk of electric shock.

Do not open.

In

Avis

8

Risque de choc electrique.

Ne pas ouvrir.

Out

Cr/Pr

Achtung

Vorm öffnen des gerätes.

Netzstecker ziehen.

SW

SR

R

R

S-Video

Component

SCART (Composite/RGB/Stereo Audio)

This product complies with DHHS rules 21 CFR, Chapter 1,

Subchapter J, Part 1040 at date of manufacture.

Apparatus claims of US patent nos. 4,631,603; 4,577,216; 4,819,098 and 4,907,093 licensed for limited viewing only.

“DTS” is a trademark of Digital Theatre Systems Inc.

Manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

Confidential Unpublished Works

©1992-1997 Dolby Laboratories. All rights reserved.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference; 2) This device must accept any interference, including interference that may cause undesired operation.

10

HDMI Out

Manufactured in an ISO9002 approved facility.

ENGLISH

1 AC power socket	8 RGB/SCART
Once you have made all audio and video connections, plug the IEC type	Use a SCART/Peritel cable to connect to the 21-pin scart input jack of a
AC power cable into the rear of the unit and an appropriate mains socket	TV. SCART carries both audio (stereo) and video (as either Composite, S-
then switch on. Your DVD player is now ready for use.	Video or RGB) at the same time.

2Power On/Off

Switches the unit on and off.

3Control Bus

In - Allows un-modulated commands from multi-rooms systems or other components to be received by the unit.

Out - Loop out for Control Bus commands to another unit.

4IR (Infra-Red) Emitter In

Allows modulated IR commands from multi-room systems or IR repeater systems to be received by the unit. Commands received here are not looped out of the Control Bus. Refer to the ‘Custom Installation’ section of this manual for more information.

5Digital Outputs

Digital audio outputs are normally used to connect to a suitable Audio/Video Receiver for surround sound decoding (output must be set for ‘RAW Bitstream’ - refer to the ‘Audio setup’ section). These outputs can also be used to connect to a separate DAC or digital recording device (output must be set for ‘PCM Stereo’ - refer to the ‘Audio setup’ section).

Toslink Optical - Use a high quality TOSLINK fibre optic cable.

S/P DIF Co-Axial Digital - Use a high quality 75 ohm digital RCA/Phono interconnect cable designed specifically for digital audio use.

65.1 Channel Audio Out

If Downmix is set to ‘Off’ in the Speaker Setup section of the 540D V2’s Setup menus, these sockets provide 5.1 output from the 540D V2's built in Dolby Digital / Pro Logic II decoder. This can be used to connect to the

5.1audio line-level inputs of an amplifier/AV receiver or amplified speaker package if required.

If Downmix is set to ‘On’, the Left and Right outputs only are active and provide a stereo downmixed output.

7Stereo Audio Out

A separate permanent Stereo output (or Stereo downmix in the case of multi-channel material) is available for connection to the analog stereo inputs of an amplifier/AV receiver etc. This is the best connection to use for listening to CDs.

9Analog Video Outputs

Composite - Connect to your television via 75 ohm RCA/phono cable designed specifically for video use.

S-Video- Connect to your television via dedicated S-Video cable.

Component - Connect to the YCbCr or YPbPr terminals of a television set via three 75 ohm RCA/phono cables designed specifically for video use.

10HDMI Out

HDMI (High-Definition Multi-Media Interface) is a purely digital connection that can carry both audio and video. Use a dedicated HDMI cable to connect to a TV/Monitor with a compatible HDMI input.

Note: The preferred connection method for video sources is always HDMI (highest quality, and can also carry audio in some circumstances) then Component Video then RGB/SCART then S- Video then Composite Video (lowest quality). The HDMI and Component outputs also support Progressive Scan which gives better picture quality if supported by your TV.

5