Portable Air Compressor
FP2051, FP2052
General Safety Information (Continued)
3.Only persons well acquainted with these rules of safe operation should be allowed to use the compressor.
4.Keep visitors away and NEVER allow children in the work area.
5.Wear safety glasses
and use hearing protection when operating the pump or unit.
6.Do not stand on or use the pump or unit as a handhold.
7.Before each use, inspect compressed air system and electrical components for signs of damage, deterioration, weakness or leakage. Repair or replace defective items before using.
8.Check all fasteners at frequent intervals for proper tightness.
! WARNING
Motors, electrical equipment and controls
can cause electrical arcs
that will ignite a flammable gas or vapor. Never operate or repair in or near a flammable gas or vapor. Never store flammable liquids or gases in the vicinity of the compressor.
!CAUTION
Compressor parts may be hot even if the unit is stopped.
9.Keep fingers away from a running compressor; fast moving and hot parts will cause injury and/or burns.
10.If the equipment should start to abnormally vibrate, STOP the engine/motor and check immediately for the cause. Vibration is generally a warning of trouble.
11.To reduce fire hazard, keep engine/motor exterior free of oil, solvent, or excessive grease.
Never remove or ! WARNING attempt to adjust
safety valve. Keep safety valve free from paint and other accumulations.
!DANGER
Never attempt to repair or modify a tank! Welding, drilling or any
other modification will weaken the tank resulting in damage from rupture or explosion. Always replace worn or damaged tanks.
Drain liquid from
! WARNING tank daily.
13.Tanks rust from moisture
14.Fast moving air will stir up dust and debris which may be harmful. Release air slowly when draining moisture or depressurizing the compressor system.
SPRAYING PRECAUTIONS
! WARNING
Do not spray flammable materials in vicinity of open flame or near ignition sources including the compressor unit.
15.Do not smoke when spraying paint, insecticides, or other flammable substances.
16.Use a face mask/
respirator when spraying and spray in a well ventilated area to prevent health and fire hazards.
17.Do not direct paint or other sprayed material at the compressor. Locate compressor as far away from the spraying area as possible to minimize overspray accumulation on the compressor.
18.When spraying or cleaning with solvents or toxic chemicals, follow the instructions provided by the chemical manufacturer.
Installation
LOCATION
It is extremely important to use the compressor in a clean, well ventilated area where the surrounding air temperature will not be more than 100°F.
A minimum clearance of 18 inches between the compressor and a wall is required because objects could obstruct air flow.
Do not locate the
! CAUTION compressor air inlet near steam, paint spray, sandblast areas or any other source of contamination. This debris will damage the motor.
GROUNDING INSTRUCTIONS
1.This product is for use on a nominal 120 volt circuit and has a grounding plug that looks like the plug illustrated in Fig. 1. Make sure the product is connected to an outlet having the same configuration as the plug. This product must be grounded. In the event of an electrical short circuit, grounding reduces risk of electrical shock by providing an escape wire for electric current. This product is equipped with a cord having a grounding wire with an appropriate grounding plug. Plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Grounding
Pin
TEST RESET
Grounded Outlet
Figure 1 - Grounding Method
!DANGER
Improper use of grounding plug can result in a possible risk of electrical shock!
Lista de Repuestos |
|
|
|
|
| FP2051, FP2052 | ||
|
|
|
|
|
|
| ||
No. de | Número del |
|
| No. de | Número del |
| ||
Ref. Descripción | repuesto | Ctd. |
| Ref. Descripción | repuesto | Ctd. | ||
|
|
|
|
|
|
|
|
|
1 | Cabezal/motor | FP205110AV | 1 | 36 | Tuerca M3x2,5 | ❍ | 2 | |
2 | Patas del chasis | ■ | 4 |
| 37 | Arandela | ❍ | 2 |
3 | Patas de la cubierta del motor | ▲ | 4 |
| 38 | Ventilador | ❍ | 1 |
4 | Cubierta izquierda del compresor | FP205111AV | 1 |
| 39 | Alivio de tensión | ∆ | 1 |
5 | Cubierta derecha del compresor | FP205112AV | 1 |
| 40 | Tornillo M4x8 | ∆ | 2 |
6 | Panel del manómetro | FP205113AV | 1 |
| 41 | Tornillo M3x10 | ❏ | 2 |
7 | Chasis | FP205114AV | 1 |
| 42 | Sujetador del cableado | ❏ | 1 |
8 | Mango | FP205115AV | 1 |
| 43 | Valvula de seguridad | 1 | |
9 | Distribuidor (incluye regulador) | FP205116AV | 1 |
| 44 | Gancho de la correa | ★ | 1 |
10 | Bandeja de accesorios | FP205117AV | 1 |
| 45 | Correa | ★ | 1 |
11 | Tubo de escape | ◆ | 1 |
| 46 | Tornillo M4x10 | ★ | 1 |
12 | Soporte de montaje para pared | ● | 1 |
| 47 | Fusible | FP205130AV | 1 |
13 | Tornillo 1/4x19 | ■ | 4 |
| 48 | Tornillo autorroscante | ▲ | 1 |
14 | Tornillo M6x15 | ■ | 4 |
| 49 | Tubo de goma | ▲ | 2 |
|
| ▼ | 4 |
| 50 | Tornillo | ▲ | 1 |
15 | Tornillo M6x200 | ▼ | 1 |
| 51 | Tuerca | ▲ | 4 |
16 | Presostato | FP205118AV | 1 |
| 52 | Placa fija del motor | ▲ | 1 |
17 | Tablero del circuito | ❏ | 1 |
| 53 | Tuerca | ▲ | 1 |
18 | Cordón eléctrico | ∆ | 1 |
| 54 | Tornillo para madera | ● | 3 |
19 | Conexión de compresión | ◆ | 2 |
| JUEGOS DE REPUESTOS |
|
| |
20 | Tuerca de compresión | ◆ | 2 |
| ▲ | Juego de montaje del motor | FP205131AV |
|
21 | Manga | ◆ | 2 |
| ■ | Juego de las patas del chasis | FP205120AV |
|
22 | Arandela de 6,4 mm (1/4”) |
|
|
| ● | Juego de montaje para pared | FP205121AV |
|
| (No se muestra) | ■ | 4 |
| ◆ | Juego de tubos | FP205122AV |
|
|
| ▼ | 4 |
| ▼ | Juego de tornillos de la cubierta | FP205123AV |
|
23 | Interruptor de encendido/apagado FP205129AV | 1 |
| ❏ | Juego del tablero de circuitos | FP205124AV |
| |
24 | Válvula de drenaje | 1 |
| ∆ | Juego del cordón de corriente | FP205125AV |
| |
25 | Accesorios de inflado | ✤ | 1 |
| † | Juego de la válvula de chequeo | FP205126AV |
|
26 | Adaptador | ✤ | 1 |
| ❍ | Juego del ventilador | FP205127AV |
|
27 | Boquilla para neumático | ✤ | 1 |
| ★ | Juego de la correa | FP205128AV |
|
28 | Tuerca de retención de la cubierta ▼ | 1 |
| ✤ | Kit de herramienta | FP204008AV |
| |
29 | Tornillo 3x8 | ▼ | 5 |
|
| Juego para calcomanía (No se muestra) |
| |
30 | Tornillo de fijación para hormigón | ● | 3 |
|
| Modelo FP2051 | FP205132AV |
|
31 | Valvula de chequeo | † | 1 |
|
| Modelo FP2052 | FP205221AV |
|
32 | Resorte | † | 1 |
|
|
|
|
|
33 | Manómetro de salida | FP006300AV | 1 |
|
|
|
|
|
34 | Manómetro del tanque | GA016304AV | 1 |
|
|
|
|
|
35 | Tornillo M3x10 | ❍ | 2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
www.chpower.com
2
27 Sp
