Cannon 10460G Burners and nozzles specifications, Installation, Earth, Neutral, Live, Liquid gas

Installation

For models supplied without a plug, fit a standard plug, suitable for the load indicated on the rating plate, onto the cable and connect to a suitable socket. To connect directly to the mains supply, a double-pole switch with a contact separation of at least 3 mm suitable for the load and complying with current standards and regulations, must be fitted between the appliance and the mains supply outlet. The yellow-green earth wire must not be interrupted by the switch. The supply cable must be in such a position that no part of it can reach a temperature of 50 °C above room temperature. For installation above a built- under oven, the hob and the oven must be connected separately to the electricity supply both for safety reasons and for easy removal of the oven if necessary. Do not use adapters or shunts as they could cause heating or burning. Before connecting to the power supply, make sure that:

•the limiter valve and the domestic system can withstand the load from the appliance (see rating plate);

•the supply system is efficiently earthed according to standards and laws in force;

•the socket or double-pole switch are easily accessible when the appliance is installed.

Important: the wires in the mains lead are coloured in accordance with the following code:

Green & Yellow	- Earth
Blue	- Neutral
Brown	- Live

As the colours of the wires in the mains lead may not

correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

Connect the Green & Yellow wire to terminal marked “E” or

or coloured Green or Green & Yellow.

Connect the Brown wire to the terminal marked “L” or coloured Red.

Connect the Blue wire to the terminal marked “N” or coloured Black.

FAILURE TO OBSERVE THE ACCIDENT-PREVENTION REGULATIONS RELIEVES THE MANUFACTURER OF ALL LIABILITY.

Replacing the cable

Use a rubber cable of the type H05RR-F with a suitable cross section 3 x 1.5 mm².

The yellow-green earth wire must be 2-3 cm longer than the other wires.

ENERGY LABEL

Directive 2002/40/EC on the label of electric ovens Norm EN 50304

Energy consumption for Natural convection

heating mode: Convection

Declared energy consumption for Forced convection Class

heating mode: Fan assisted

Burners and nozzles specifications

Table 1						Liquid gas				Natural gas
	Diameter	Thermal power			By-pass	Injector	Flow *			Injector	Flow*
	(mm)	kW (H.s.*)			1/100	1/100		g/h		1/100	l/h
BURNER		Nomin.		Reduc.	(mm)	(mm)	G30		G31	(mm)	G20
C.Rapid	100	3.00		0.7	40	86	218		214	116	286
B. Semi-rapid	75	1.65		0.4	30	64	120		118	96	157
A. Auxiliary	55	1.00		0.3	27	50	73		71	71	95
D. Double flame DC DR (internal)	30	0.90		0.4	30	44	65		64	70	86
D. Double Flame DC DR (external)	130	4.10		1.3	57	70	298		293	110	390
				Nominal			28-30		37		20
Supply pressure				Minimum			20		25		17
			Maximum				35		45		25

This appliance conforms with the following European Economic Community directives:

-73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications;

-89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications;

-90/396/EEC of 29/06/90 (Gas) and subsequent modifications;

-93/68/EEC of 22/07/93 and subsequent modifications.

*At 15°C and 1013 mbar-dry gas Propane G31 H.s. = 50,37 MJ/kg

Butane G30 H.s. = 49,47 MJ/kg Natural gas G20 H.s. = 37,78 MJ/m3

17