|
|
|
| Trouble? | 79 | ||
|
|
|
| ||||
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |
| Problem |
| Solution |
|
|
| |
|
|
| |||||
|
|
|
|
|
|
| |
| No sound from the | Open the LCD panel. |
|
|
| – | |
| speaker. | Speaker volume is turned off. Adjust the volume with the |
| ||||
|
|
| |||||
|
| [SPEAKER VOLUME] setting. |
|
|
| ||
| Image will not appear on the | Check again that the camcorder is properly connected to the TV. |
| ||||
| TV screen. |
|
|
|
|
|
|
| Tape is running, but image will | TV/VIDEO selector on the TV is not set to VIDEO. Set the |
| ||||
| not appear on the TV screen. | selector to VIDEO. |
|
|
|
|
|
|
| Video heads are dirty. Clean the video heads. |
| ||||
|
| You attempted to play back or dub copyright a protected tape. |
| ||||
|
| Stop playback/dubbing. |
|
|
|
|
|
| Memory Card Operation |
|
|
|
|
|
|
|
|
|
|
|
| ||
| Problem |
| Solution |
|
|
| |
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| Memory card cannot be | Memory card was not facing the correct direction. Turn the |
| ||||
| inserted. | memory card over and reinsert it. |
|
|
| ||
| Cannot record on the memory | Memory card is full. Erase still images to free some space or |
| ||||
| card. | replace the memory card. |
|
|
| ||
|
| Memory card was not initialized. Initialize the memory card. |
| ||||
|
| The folder and file numbers have reached their maximum value. |
| ||||
|
| Set [FILE NOS.] to [RESET] and insert a new memory card. |
|
|
| ||
| Memory card cannot be played | Set the camcorder to | . |
|
| ||
| back. |
|
|
|
|
|
|
| Image cannot be erased. | Image is protected. Cancel the protection. |
| ||||
|
| The |
| – | |||
|
| to prevent accidental erasure. Change the position of the write- |
|
|
| ||
|
| protect switch. |
|
|
|
|
|
| “ ” flashes in red. | Card error occurred. Turn off the camcorder. Remove and |
| ||||
|
| reinsert the memory card. Initialize the memory card if flashing |
|
|
| ||
|
| persists. |
|
|
|
|
|
| Printing |
|
|
|
|
|
|
|
|
|
|
|
| ||
| Problem |
| Solution |
|
|
| |
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| The printer is not operating | Disconnect the USB cable and turn off the camcorder and the |
| – | |||
| even though the camcorder | printer. After a short while, turn them on again, set the |
|
|
| ||
| and printer are correctly | camcorder to | mode and restore the connection. |
|
|
| |
| connected. |
|
|
|
|
|
|
| Editing |
|
|
|
|
|
|
|
|
|
|
|
| ||
| Problem |
| Solution |
|
|
| |
|
|
|
|
|
|
|
|
| Cannot record with this | Wrong signal standard. Refer also to the instruction manual of |
| – | |||
| camcorder video input from an | the connected device. |
|
|
|
|
|
| external video device |
|
|
|
|
|
|
| connected using a DV cable. |
|
|
|
|
|
|
Information Additional