Carrier 17EX specifications Starts Limit Exceeded, Autorestart in Progress

Table 12 Ð LID Primary and Secondary Messages and Custom Alarm/Alert Messages

with Troubleshooting Guides (cont)

D. PRE-START ALERTS: These alerts only delay start-up. When alert is corrected, the start-up will continue. No reset is necessary.

PRIMARY MESSAGE	SECONDARY MESSAGE		ALARM MESSAGE/PRIMARY CAUSE	ADDITIONAL CAUSE/REMEDY
PRESTART ALERT	STARTS LIMIT EXCEEDED	STARTS EXCESSIVE Compressor Starts (8 in		Depress the RESET softkey if additional start is
		12 hours)		required. Reassess start-up requirements.
PRESTART ALERT	HIGH MOTOR TEMPERATURE	MTRW [VALUE] exceeded limit of [LIMIT]*.		Check motor cooling line for proper operation.
		Check motor temperature.		Check for excessive starts within a short time
				span.
PRESTART ALERT	HIGH BEARING TEMPERATURE	MTRB [VALUE] exceeded limit of [LIMIT]*.		Check oil heater for proper operation, check for
		Check thrust bearing temperature.		low oil level, partially closed oil supply valves,
				etc. Check sensor accuracy.
PRESTART ALERT	HIGH DISCHARGE TEMP	CMPD [VALUE] exceeded limit of [LIMIT]*.		Check sensor accuracy. Allow discharge tem-
		Check discharge temperature.		perature to cool. Check for excessive starts.
PRESTART ALERT	LOW REFRIGERANT TEMP	ERT [VALUE] exceeded limit of [LIMIT]*. Check		Check transducer accuracy. Check for low chilled
		refrigerant temperature.		water/brine supply temperature.
PRESTART ALERT	LOW OIL TEMPERATURE	OILT [VALUE] exceeded limit of [LIMIT]*.		Check oil heater power, oil heater relay. Check
		Check oil temperature.		oil level.
PRESTART ALERT	LOW LINE VOLTAGE	V	P [VALUE] exceeded limit of [LIMIT]*.	Check voltage supply. Check voltage transform-
		Check voltage supply.		ers. Consult power utility if voltage is low. Cali-
				brate voltage reading on STATUS01 Table.
PRESTART ALERT	HIGH LINE VOLTAGE	V	P [VALUE] exceeded limit of [LIMIT]*.	Check voltage supply. Check voltage transform-
		Check voltage supply.		ers. Consult power utility if voltage is low. Cali-
				brate voltage reading on STATUS01 table.
PRESTART ALERT	HIGH CONDENSER PRESSURE	CRP [VALUE] exceeded limit of [LIMIT]*. Check		Check for high condenser water temperature.
		condenser water and transducer.		Check transducer accuracy.
PRESTART ALERT	HIGH GEAR OIL TEMP	GEAOILT [VALUE] exceeded limit of [LIMIT].*		Check for cooler water ¯ow. Check sensor for
		Check gear oil cooler ¯ow.		accuracy.

*[LIMIT] is shown on the LID as temperature, pressure, voltage, etc., set point prede®ned or selected by the operator as an override, alert, or alarm condition. [VALUE] is the actual pressure, temperature, voltage, etc., at which the control tripped.

E. NORMAL OR AUTO.-RESTART

PRIMARY MESSAGE	SECONDARY MESSAGE	PROBABLE CAUSE/REMEDY
STARTUP IN PROGRESS	OCCUPIED MODE	Chiller starting. Time schedule is occupied.
STARTUP IN PROGRESS	REMOTE CONTACT CLOSED	Chiller starting. Remote contacts are closed.
STARTUP IN PROGRESS	START COMMAND IN EFFECT	Chiller starting. Chiller START/STOP on STATUS01 manually forced
		to start.
AUTORESTART IN PROGRESS	OCCUPIED MODE	Chiller starting. Time schedule is occupied.
AUTORESTART IN PROGRESS	REMOTE CONTACT CLOSED	Chiller starting. Remote contacts are closed.
AUTORESTART IN PROGRESS	START COMMAND IN EFFECT	Chiller starting. Chiller START/STOP on STATUS01 manually forced
		to start.

F. SPARE SENSOR ALERT MESSAGES

PRIMARY MESSAGE	SECONDARY MESSAGE	ALARM MESSAGE/PRIMARY CAUSE	ADDITIONAL CAUSE/REMEDY
SPARE SENSOR ALERT	COMMON CHWS SENSOR	Sensor Fault: Check common CHWS sensor.
SPARE SENSOR ALERT	COMMON CHWR SENSOR	Sensor Fault: Check common CHWR
		sensor.
SPARE SENSOR ALERT	REMOTE RESET SENSOR	Sensor Fault: Check remote reset tempera-
		ture sensor.
SPARE SENSOR ALERT	TEMP SENSOR Ð SPARE 1	Sensor Fault: Check temperature sensor Ð
		Spare 1.
SPARE SENSOR ALERT	TEMP SENSOR Ð SPARE 2	Sensor Fault: Check temperature sensor Ð
		Spare 2.
SPARE SENSOR ALERT	TEMP SENSOR Ð SPARE 3	Sensor Fault: Check temperature sensor Ð	Check alert temperature set points on EQUIP-
		Spare 3.
			MENT SERVICE table, SERVICE2 screen.
SPARE SENSOR ALERT	TEMP SENSOR Ð SPARE 4	Sensor Fault: Check temperature sensor Ð
			Check sensor for accuracy if reading is not
		Spare 4.
			accurate.
SPARE SENSOR ALERT	TEMP SENSOR Ð SPARE 5	Sensor Fault: Check temperature sensor Ð
		Spare 5.
SPARE SENSOR ALERT	TEMP SENSOR Ð SPARE 6	Sensor Fault: Check temperature sensor Ð
		Spare 6.
SPARE SENSOR ALERT	TEMP SENSOR Ð SPARE 7	Sensor Fault: Check temperature sensor Ð
		Spare 7.
SPARE SENSOR ALERT	TEMP SENSOR Ð SPARE 8	Sensor Fault: Check temperature sensor Ð
		Spare 8.
SPARE SENSOR ALERT	TEMP SENSOR Ð SPARE 9	Sensor Fault: Check temperature sensor Ð
		Spare 9.

87