Convenience
Outlet
GFCI
Pwd-CO
Fuse
Switch 
Pwd-CO
Transformer
Control Box
Access Panel
Fig. 10 — Convenience Outlet Location
Non-powered type: This type requires the field installation of a general-purpose 125-volt 15-A circuit powered from a source elsewhere in the building. Observe national and local codes when selecting wire size, fuse or breaker requirements and disconnect switch size and location. Route 125-v power supply conductors into the bottom of the utility box containing the duplex receptacle.
Unit-powered type: A unit-mounted transformer is factory- installed to stepdown the main power supply voltage to the unit to 115-v at the duplex receptacle. This option also includes a manual switch with fuse, located in a utility box and mounted on a bracket behind the convenience outlet; access is through the unit's control box access panel. See Fig. 10.
The primary leads to the convenience outlet transformer are not factory-connected. Selection of primary power source is a customer-option. If local codes permit, the transformer primary leads can be connected at the line-side terminals on the unit- mounted non-fused disconnect or HACR breaker switch; this will provide service power to the unit when the unit disconnect switch or HACR switch is open. Other connection methods will result in the convenience outlet circuit being de-energized when the unit disconnect or HACR switch is open. See Fig. 11.
12
| UNIT | CONNECT | PRIMARY | TRANSFORMER |
| VOLTAGE | AS | CONNECTIONS | TERMINALS |
| 208, | 240 | L1: RED + YEL | H1 + H3 |
| 230 | L2: BLU + GRA | H2 + H4 |
| |
| | | L1: RED | H1 |
| 460 | 480 | Splice BLU + |
| H2 + H3 |
| YEL |
| | | H4 |
| | | L2: GRA |
| | | |
| 575 | 600 | L1: RED | H1 |
| L2: GRA | H2 |
| | |
| UNIT | CONNECT | PRIMARY | TRANSFORMER |
| VOLTAGE | AS | CONNECTIONS | TERMINALS |
| 208, | 240 | L1: RED + YEL | H1 + H3 |
| 230 | L2: BLU + GRA | H2 + H4 |
| |
| | | L1: RED | H1 |
| | | Splice BLU + |
| 460 | 480 | H2 + H3 |
| YEL |
| | | H4 |
| | | L2: GRA |
| | | |
| 575 | 600 | L1: RED | H1 |
| L2: GRA | H2 |
| | |
Fig. 11 - Powered Convenience Outlet Wiring
Duty Cycle: the unit-powered convenience outlet has a duty cycle limitation. The transformer is intended to provide power on an intermittent basis for service tools, lamps, etc; it is not intended to provide 15-amps loading for continuous duty loads (such as electric heaters for overnight use). Observe a 50% limit on circuit loading above 8-amps (i.e., limit loads exceeding 8-amps to 30 minutes of operation every hour).
Test the GFCI receptacle by pressing the TEST button on the face of the receptacle to trip and open the receptacle. Check for proper grounding wires and power line phasing if the GFCI re- ceptacle does not trip as required. Press the RESET button to clear the tripped condition.
Fuse on power type: The factory fuse is a Bussman “Fusetron” T-15, non-renewable screw-in (Edison base) type plug fuse.
Using unit-mounted convenience outlets: Units with unit- mounded convenience outlet circuits will often require that two disconnects be opened to de-energize all power to the unit. Treat all units as electrically energized until the convenience outlet power is also checked and de-energization is confirmed. Observe National Electrical Code Article 210, Branch Circuits, for use of convenience outlets.
Installing Weatherproof Cover
A weatherproof while-in-use cover for the factory-installed convenience outlets is now required by UL standards. This cover cannot be factory-mounted due its depth; it must be installed at unit installation. For shipment, the convenience outlet is covered with a blank cover plate.
The weatherproof cover kit is shipped in the unit's control box. The kit includes the hinged cover, a backing plate and gasket.
DISCONNECT ALL POWER TO UNIT AND CONVENIENCE OUTLET.
Remove the blank cover plate at the convenience outlet; discard the blank cover.
Loosen the two screws at the GFCI duplex outlet, until approximately 1/2-in (13 mm) under screw heads are exposed.
