23 Program your Keyless Entry
Activate the opener only when door is in full view, free of obstruction and properly adjusted. No one should enter or leave garage while door is in motion. Do not allow children to operate push button(s) or remote(s). Do not allow children to play near the door.
NOTE: Your new Keyless Entry must be programmed to operate your garage door opener.
Program the Receiver to Match Additional Remote Control Code Using the orange “LEARN” Button:
1.Press and release the orange “learn” button (1) on opener. The learn indicator light will glow steadily for 30 seconds.
2.Within 30 seconds, enter a four digit personal identification number (PIN) of your choice on the keypad (2), then press and hold the ENTER button.
3.Release the button when the opener light blinks (3). It has learned the code. If the light bulb is not installed, two clicks will be heard.
NOTE: This method requires two people if the Keyless Entry is already mounted outside the garage.
Using the Multi-Function Door Control:
1.Enter a four digit personal identification number (PIN) of your choice on the keypad, then press and hold ENTER.
2.While holding the ENTER button, press and hold the LIGHT button on the
3.Continue holding the ENTER and LIGHT buttons while you press the push bar on the
4.Release buttons when the opener light blinks. It has learned the code. If the light bulb is not installed, two clicks will be heard.
24 Using the Wall-Mounted Door Control
THE
Press the push bar (1) to open or close the door. Press again to stop the door.
Light feature
Press the Light button (2) to turn the opener light on or off. It will not control the opener light when the door is in motion. If you turn it on and then activate the opener, the light will remain on for
Lock feature
Designed to prevent operation of the door from
To activate, press and hold the Lock button (3) for 2 seconds. The push bar light will flash as long as the Lock feature is on.
To turn off, press and hold the Lock button again for 2 seconds.The push bar light will stop flashing. The Lock feature will also turn off whenever the “LEARN” button on the opener panel is activated.
ADJUSTMENT SECTION
25 Setting the Limits
Travel limits regulate the points at which the door will stop when moving up or down. Follow the steps below to set the limits.
To program the travel limits:
1.Open the light lens. Press and hold the black button (1) until the yellow indicator light (3) starts flashing slowly and then release.
2.Push and hold the black button (1) until the door reaches the desired open position. Adjust the position of the door by using the black (1) and orange (2) buttons. Black moves the door UP, orange moves the door DOWN.
3.Push the programmed remote control (4) or push bar on the door control that was shipped with your opener. This sets the full UP (open) position. The door will travel to the floor and reverse back to the UP (open) position. The opener has learned its travel limits.
Check to be sure the door is high enough for your vehicle. Adjust if necessary.
4.The indicator light (3) will stop flashing when the limits have been learned.
If the door reverses before it reaches the floor repeat steps
The force MUST be learned in order to properly complete the setting of the limits.
NOTE: The worklight blinks 10 times whenever the Limits Setting routine fails. If you get this error, proceed to #15 of the Having a Problem? section and follow the instructions for setting the limits manually.
26 Setting the Force
The force setting button is located behind the light lens of the opener. The force setting regulates the amount of power required to open and close the door.
1.Open the light lens. Locate the orange button (2).
2.Push the orange button (2) twice to enter unit into Force Adjustment Mode. The LED (3) (indicator light) will flash quickly.
3.Push the programmed remote control (4) or push bar on the door control that was shipped with your opener. The door will travel to the DOWN (close) position. Push the remote control (4) again, the door will travel to the UP (open) position.
The LED (3) (indicator light) will stop flashing when the force has been learned.
The door must travel through a complete cycle, UP and DOWN, in order for the force to be set properly. If the unit cannot open and close your door fully, inspect your door to insure that it is balanced properly and is not sticking or binding.
27 Test the Safety Reverse System
The safety reverse system test is important. Garage door must reverse on contact with a 40mm obstacle laid flat on the floor. Failure to properly adjust opener may result in serious personal injury from a closing garage door. Repeat test once a month and adjust as needed.
Procedure: Place a 40mm obstacle (1) laid flat on the floor under the garage door. Operate the door in the down direction. The door must reverse on the obstruction. If the door stops on the obstruction, remove obstruction and repeat Setting the Limits step 25. Repeat test.
When the door reverses on the 40mm obstacle, remove the obstruction and run the opener through a complete travel cycle. Door must not reverse in closed position. If it does, repeat Setting the Limits and Force steps 25 and 26 and repeat safety reverse test.
Place 20kg at the center of the door and ensure that the door will not move up more than 500mm.
