Manuals / Brands / Baby / Safety Gate / Chamberlain / Baby / Safety Gate

Chamberlain SL 1000-X3 K. BASIC GATE OPERATOR PROGRAMMING, Step, To access, To program, To exit, Purpose, # of, Default, Acceptable Input, Digits, NOTES:

1 44

Download 44 pages, 4.44 Mb

18

K. BASIC GATE OPERATOR PROGRAMMING

Even if you plan to program the gate operator by telephone, you may want to enter some immediate instructions during installation. The following list of instructions will help you set basic controls so the gate will operate properly until you have time for full programming, either directly or by telephone. For complete programming instructions, refer to the SL 1000, SW 2000, BG 3000 Programming Manual.

To access programming mode: enter ✱✱✱ 000000 (3 asterisks, 6 zeroes)

To program a command: a) enter step number b) enter required data c) enter # (pound sign)

To exit programming mode: enter 00# (2 zeroes, 1 pound sign)

Step	Purpose	# of	Default		Acceptable Input
		Digits
01	Gate Type	1	1	0	= Slide, 1 = Swing, 2 =
	(See Notes Below)			Barrier,
	(See Notes Below)			3	= Linear
				3	= Linear
02	Operator Type	1	0	0	= Single, 1 = Master, 2 =
				Slave

03	Pair Type	1	0	0=Bipart, 1=Latch, 2=Not
				Used, 3=Tandem
04	Not Used	-	-	-

05	Not Used	-	-	-
06	Anti-Tailgate Enable (ATG)	1	0	0	= Disabled, 1 = Enabled

07	Latch Delay Time	3	6	0	– 250 Seconds (.4 sec.
				Increments)
08	Reclose Time (RT)	Up to 3	30	0	– 250 Seconds (0 =
				Disabled)

09	Not Used	-	-	-
10	Not Used	-	-	-

11	Obstruction Sense Backup	Up to 3	12	2	– 499 Inches
	Closing

12	Obstruction Sense Backup	Up to 3	12	2	– 499 Inches
	Opening
13	Interrupt Bar Backup If Closing	Up to 3	12	2	– 499 Inches
14	Interrupt Bar Backup If Opening	Up to 3	12	2	– 499 Inches
15	Return to Factory Set Defaults	6	N/A	101010 (partial), 191919 (full)

NOTES:

1.If Gate Type is set to SLIDE, gate brakes whenever it stops.

2.If Gate Type is set to SWING, gate brakes only when it reaches the open or close limit.

1.If Gate Type is set to BARRIER or LINEAR, the gate never brakes.

Rev J

Doc 01-20098

Page 18 of 44

Contents

E STAT E SERIES MODEL SL MODEL SL 1000-X3IS FOR VEHICULAR PASSAGE GATES ONLY, NOT INTENDED FOR PEDESTRIAN PASSAGE GATE USE 3 YEAR WARRANTY TABLE OF CONTENTS The LiftMaster Gate Operator Model SL SAFETY SUMMARY BASIC INSTALLATION HINTS AND RULES SITE PREPARATION A. LOCATION AND LAYOUT Figure 1. Front Drive Figure 2. Rear Drive Figure 3. Mid Drive B. PAD AND MOUNT Figure 4. Pad and Track Ribbon Figure 5. Bolt Down Pattern Figure 6. Conduit Entrance Areas C.POWER WIRING D.LOOP DETECTORS AND PHOTO-SENSORS E.TELEPHONE CONNECTION F. OTHER CONNECTIONS G. MASTER/SLAVE INTERCONNECTION (MASTER/SLAVE SYSTEM ONLY) PART SYSTEM INSTALLATION A. GATE AND PHOTO-SENSORLAYOUT B. MOUNTING GATE OPERATOR 2.Installing Chain and Anchors (Front Drive Gate Installation) Figure 10-A.Anchor and Chain Connector Figure 10-B.Parallel Chain Location NOTE: For rear and mid drive installations, see Figures 2 and C. QUICK DISCONNECT OPERATION D. CONNECTING POWER CAUTION Figure 11. AC Wiring E. RUNNING INPUT WIRING F. SETTING GATE OPEN DIRECTION SWITCHES S2 AND S3 G.POWER UP PROCEDURE H. USING MANUAL CONTROLS IMPORTANT NOTE I.SETTING LIMIT CAMS J. GATE SENSITIVITY ADJUSTMENTS "OPEN TO LEFT" ADJUSTMENT PROCEDURES Left Gate Motion Adjustment (R160) Right Gate Motion Adjustment (R69) START-UPCurrent Adjustment (R203) K. BASIC GATE OPERATOR PROGRAMMING To access To program To exit Step L. CONNECTING INPUT WIRING M.POST INSTALLATION PROCEDURES 5. Entry inputs 6. Alternate Action 7. Reclose Timer (RT) 8. Inside Interrupt Loop and Anti-Tailgating(ATG) When Exiting GATE TYPE is SLIDE Figure 17. Photo-SensorCoverage Areas 9. Photo-Sensors(Secondary Obstruction Sensing per UL 325) Coverage Area A (Inside-OpenCoverage): Coverage Area B (Inside-ClosedCoverage): Coverage Area C (Outside-ClosedCoverage): N. FINAL ASSEMBLY OF GATE OPERATOR Figure 18. Gate Operator Final Assembly IMPORTANT SAFETY PROCEDURE 2.Make sure that gate operator unit power switch is turned on WARNING Page TROUBLESHOOTING AND MAINTENANCE A. TROUBLESHOOTING Page 13.GATE DOES NOT CLOSE AUTOMATICALLY 14.ALTERNATE ACTION DOES NOT WORK 15.GATE DOES NOT OPEN TO THE CORRECT DIRECTION 16.THERE IS SLACK OR PLAY IN THE GATE 17.ATG (ANTI-TAILGATE)DOES NOT WORK B. FAULT LIST C.FAULTS AND THEIR CAUSES 4.IF STUCK-LIMITLED IS TURNED ON 5.IF MAX RUN TIME LED IS TURNED ON D. MAINTENANCE 2. PREVENTIVE MAINTENANCE INSTRUCTIONS Figure 23. Gate Operator Disassembly and Assembly Gate Operator Serial Number: UPS: Yes 1.Turn off power to the gate operator at the circuit breaker MAINTENANCE SCHEDULE TABLE Date Gate Chain Sprocket APPENDIX A SYSTEM OPERATION REFERENCE FUNCTIONAL INPUTS MANUAL INPUTS: OPEN, CLOSE, AND STOP (TB2) Continuous activation holds gate open gate closed INSIDE/OUTSIDE INTERRUPT LOOP DETECTOR (TB16) SWING LINEAR SLIDE BARRIER OBSTRUCTION ALARM (TB17) LOW BATTERY/ NO AC POWER (TB18) 24VAC OUTPUT (TB7) MAGLOCK INPUT (TB4) SLAVE I/O INPUT (TB1) APPENDIX B: SL 1000-X3PARTS LIST Figure 24. Exploded View GLOSSARY FCC REQUIREMENTS NOTICE TO CANADIAN USERS OPERATOR NOTES FOR TECHNICAL SUPPORT OR TO ORDER REPLACEMENT PARTS, CALL OUR TOLL FREE NUMBER: