Manuals / Brands / Computer Equipment / Network Router / Cisco Systems / Computer Equipment / Network Router

Cisco Systems 1300 Declaration of Conformity for RF Exposure, Guidelines for Operating Cisco Aironet Access Points and Bridges in Japan

1 118

Download 118 pages, 2.45 Mb

B-6

Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide

OL-5048-06

AppendixB Declarations of Conformity and Regulatory Information

Declaration of Conformity for RF Exposure

Note Combinations of power levels and antennas resulting in a radiated power level of above 100 mW eirp are

considered as not compliant with the above mentioned directive and are not allowed for use within the

European community and countries that have adopted the Europe an R&TTE directive 1999/5/EC and/or

the CEPT recommendation Rec 70.03. For more details on legal co mbinations of power levels and

antennas, contact Cisco Corporate Compliance.

Declaration of Conformity for RF Exposure

The radio module has been evaluated under FCC Bulletin OET 65C and found compliant to the

requirements in CFR 47 Sections 2.1091, and 15.247 (b) (4) addressing RF Exposure from radio

frequency devices. The AIR-ANT3338 dish antenna should be installed more than 22 c m from your body

or nearby persons. All other antennas should be installed more than 20 cm from your body or nearby

persons.

Guidelines for Operating Cisco Aironet Access Points and Bridges in Japan

This section provides guidelines for avoiding interference when operating Cisco Aironet access points

in Japan. These guidelines are provided in both Japanese and E nglish.

Japanese Translation

03-6434-6500

43768

Contents

Main Page CONTENTS Page Page Page vii HLoad-Dump Protection for Transportation Vehicles H-1 Load-Dump Protection Page Preface Audience Purpose Organization Conventions xi Related Publications Obtaining Documentation Cisco.com Product Documentation DVD Ordering Documentation Documentation Feedback Cisco Product Security Overview Reporting Security Problems in Cisco Products Product Alerts and Field Notices Obtaining Technical Assistance Cisco Support Website xvi Locating the Product Serial Number The access point/bridge serial number is located on the bottom of the cabinet (ref er to Figure 1). Figure1 Location of Access Point Serial Number Label Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Page Page Overview Product Terminology Autonomous Access Point/Bridge Lightweight Access Point Guidelines for Using a Lightweight Access Point/Bridge Key Features Power Integrated Antenna External Antenna Ethernet Ports Enclosure Connectors LEDs Operating Roles for the Autonomous Access Point/Bridge Network Examples with Autonomous Access Point/Bridges Repeater Unit that Extends Wireless Range Root Access Point on a Wired LAN Central Unit in an All-Wireless Network Bridge Network with Wireless Clients Point-to-Point Bridge Configuration Workgroup Bridge Network Network Examples with Lightweight Access Points Page Installation Overview 2-2 Safety Warnings All Installations Outdoor and DC Power Source Installations DC Power Source Installations Safety Information FCC Safety Compliance Statement Safety Precautions Page Typical Outdoor Installation Components Installation Guidelines Site Surveys Unpacking the Access Point/Bridge Package Contents Before Beginning the Installation Page Installation Summary Page Mounting Overview Mounting the Access Point/Bridge Mounting Hardware Window Mounting Multi-Function Mount Access Point Bracket Mast Bracket LEDs Autonomous Access Point/Bridge Aligning the Autonomous Bridge Antenna Using RSSI LED Indications Page Page Troubleshooting Autonomous Access Points and Bridges Checking the LEDs on an Autonomous Access Point/Bridge Normal Mode LED Indications for an Autonomous Access Point/Bridge Page Page Power Injector Checking Power Checking Basic Configuration Settings Default IP Address Behavior Default SSID and Radio Behavior Enabling the Radio Interface SSID Security Settings Antenna Alignment Running the Carrier Busy Test Running the Ping or Link Test Resetting the Autonomous Access Point/Bridge to the Default Configuration Using the Web-Browser Interface Using the CLI on an Autonomous Access Point/Bridge Reloading the Access Point/Bridge Image Web-Browser Interface Browser HTTP Interface Browser TFTP Interface Obtaining the Autonomous Access Point/Bridge Image File Connecting to the Console Serial Port Obtaining the TFTP Server Software Page Troubleshooting Lightweight Access Points Checking the LEDs on Lightweight Access Points LED Indications Power Injector Checking Power Using DHCP Option 43 Manually Configuring Controller Information Using the Access Point CLI Connecting to the Console Serial Port Configuring Controller Information Clearing Manually Entered Controller Information Manually Resetting the Access Point to Defaults Returning the Access Point to Autonomous Mode Using a Controller to Return the Access Point to Autonomous Mode tftp-server-ip-address filename access-point-name Obtaining the Autonomous Access Point Image File Page A Translated Safety Warnings Page B Declarations of Conformity and Regulatory Information Manufacturers Federal Communication Commission Declaration of Conformity Statement Tested To Comply With FCC Standards FOR HOME OR OFFICE USE VCCI Statement for Japan Industry Canada Canadian Compliance Statement Page Page Declaration of Conformity for RF Exposure Guidelines for Operating Cisco Aironet Access Points and Bridges in Japan Japanese Translation 03-6434-6500 Administrative Rules for Cisco Aironet Access Points and Bridges in Taiwan All Access Points and Bridges Chinese Translation Page Operation of Cisco Aironet Access Points in Brazil Access Point Models Regulatory Information Portuguese Translation Declaration of Conformity Statements Declaration of Conformity Statements for European Union Countries Page Page C Access Point Specifications Page Page Page D Channels and Maximum Power Levels Page E Console Serial Cable Pinouts Overview Signals and Pinouts F Priming Lightweight Access Points Prior to Deployment Page Page Page G Configuring DHCP Option 43 for Lightweight Access Points Overview Configuring Option 43 for 1000 and 1500 Series Lightweight Access Points Configuring Option 43 for 1100, 1130, 1200, 1240, and 1300 Series Access Points H Load-Dump Protection for Transportation Vehicles Load-Dump Protection Page GLOSSARY Numeric A B C D E F G I N O P Q S T U W Page INDEX A B C R S T U