Cisco Systems 1300 Safety Information

2-3

Cisco Aironet 1300 Series Wireless Outdoor Access Point/Bridge Hardware Installation Guide

OL-5048-06

Chapter2 Installation Overv iew

Safety Information

installation and grounding of the antenna, please refer to national and local codes (e.g. U.S.:NFPA 70,

National Electrical Code, Article 810, in Canada: Canadian Electrical Code, Section 54).

Statement 1052

Outdoor and DC Power Source Installations

The following warning applies to outdoor and DC power source install ations:

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

DC Power Source Installations

The following warnings apply to DC power source installations using the optional LR2T power injector:

Warning

A readily accessible two-poled disconnect device must be incorporated in the fixed wiring.

Statement 1022

Warning

Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV)

requirements in IEC 60950 based safety standards.

Statement 1033

Safety Information

Follow the guidelines in this section to ensure proper operation and safe use of the access point/bridge.

FCC Safety Compliance Statement

The FCC, with its action in ET Docket 96-8, has adopted a safety standard for human exposure to RF

electromagnetic energy emitted by FCC-certified equipment. When used with approved Cisco Aironet

antennas, Cisco Aironet products meet the uncontrolled environmental limits found in OET-65 and ANSI

C95.1, 1991. Proper operation of this radio device according to the instruct ions in this publication results

in user exposure substantially below the FCC recommended limits.

Safety Precautions

Warning

Do not locate the antenna near overhead power lines or other electric light or power circuits, or

where it can come into contact with such circuits. When installing the antenna, take extreme care

not to come into contact with such circuits, as they may cause serious injury or death. For proper

installation and grounding of the antenna, please refer to national and local codes (e.g. U.S.:NFPA 70,

National Electrical Code, Article 810, in Canada: Canadian Electrical Code, Section 54).

Statement 1052

Contents

Main Page CONTENTS Page Page Page vii HLoad-Dump Protection for Transportation Vehicles H-1 Load-Dump Protection Page Preface Audience Purpose Organization Conventions xi Related Publications Obtaining Documentation Cisco.com Product Documentation DVD Ordering Documentation Documentation Feedback Cisco Product Security Overview Reporting Security Problems in Cisco Products Product Alerts and Field Notices Obtaining Technical Assistance Cisco Support Website xvi Locating the Product Serial Number The access point/bridge serial number is located on the bottom of the cabinet (ref er to Figure 1). Figure1 Location of Access Point Serial Number Label Submitting a Service Request Definitions of Service Request Severity Obtaining Additional Publications and Information Page Page Overview Product Terminology Autonomous Access Point/Bridge Lightweight Access Point Guidelines for Using a Lightweight Access Point/Bridge Key Features Power Integrated Antenna External Antenna Ethernet Ports Enclosure Connectors LEDs Operating Roles for the Autonomous Access Point/Bridge Network Examples with Autonomous Access Point/Bridges Repeater Unit that Extends Wireless Range Root Access Point on a Wired LAN Central Unit in an All-Wireless Network Bridge Network with Wireless Clients Point-to-Point Bridge Configuration Workgroup Bridge Network Network Examples with Lightweight Access Points Page Installation Overview 2-2 Safety Warnings All Installations Outdoor and DC Power Source Installations DC Power Source Installations Safety Information FCC Safety Compliance Statement Safety Precautions Page Typical Outdoor Installation Components Installation Guidelines Site Surveys Unpacking the Access Point/Bridge Package Contents Before Beginning the Installation Page Installation Summary Page Mounting Overview Mounting the Access Point/Bridge Mounting Hardware Window Mounting Multi-Function Mount Access Point Bracket Mast Bracket LEDs Autonomous Access Point/Bridge Aligning the Autonomous Bridge Antenna Using RSSI LED Indications Page Page Troubleshooting Autonomous Access Points and Bridges Checking the LEDs on an Autonomous Access Point/Bridge Normal Mode LED Indications for an Autonomous Access Point/Bridge Page Page Power Injector Checking Power Checking Basic Configuration Settings Default IP Address Behavior Default SSID and Radio Behavior Enabling the Radio Interface SSID Security Settings Antenna Alignment Running the Carrier Busy Test Running the Ping or Link Test Resetting the Autonomous Access Point/Bridge to the Default Configuration Using the Web-Browser Interface Using the CLI on an Autonomous Access Point/Bridge Reloading the Access Point/Bridge Image Web-Browser Interface Browser HTTP Interface Browser TFTP Interface Obtaining the Autonomous Access Point/Bridge Image File Connecting to the Console Serial Port Obtaining the TFTP Server Software Page Troubleshooting Lightweight Access Points Checking the LEDs on Lightweight Access Points LED Indications Power Injector Checking Power Using DHCP Option 43 Manually Configuring Controller Information Using the Access Point CLI Connecting to the Console Serial Port Configuring Controller Information Clearing Manually Entered Controller Information Manually Resetting the Access Point to Defaults Returning the Access Point to Autonomous Mode Using a Controller to Return the Access Point to Autonomous Mode tftp-server-ip-address filename access-point-name Obtaining the Autonomous Access Point Image File Page A Translated Safety Warnings Page B Declarations of Conformity and Regulatory Information Manufacturers Federal Communication Commission Declaration of Conformity Statement Tested To Comply With FCC Standards FOR HOME OR OFFICE USE VCCI Statement for Japan Industry Canada Canadian Compliance Statement Page Page Declaration of Conformity for RF Exposure Guidelines for Operating Cisco Aironet Access Points and Bridges in Japan Japanese Translation 03-6434-6500 Administrative Rules for Cisco Aironet Access Points and Bridges in Taiwan All Access Points and Bridges Chinese Translation Page Operation of Cisco Aironet Access Points in Brazil Access Point Models Regulatory Information Portuguese Translation Declaration of Conformity Statements Declaration of Conformity Statements for European Union Countries Page Page C Access Point Specifications Page Page Page D Channels and Maximum Power Levels Page E Console Serial Cable Pinouts Overview Signals and Pinouts F Priming Lightweight Access Points Prior to Deployment Page Page Page G Configuring DHCP Option 43 for Lightweight Access Points Overview Configuring Option 43 for 1000 and 1500 Series Lightweight Access Points Configuring Option 43 for 1100, 1130, 1200, 1240, and 1300 Series Access Points H Load-Dump Protection for Transportation Vehicles Load-Dump Protection Page GLOSSARY Numeric A B C D E F G I N O P Q S T U W Page INDEX A B C R S T U