Cisco Systems manual 3-18, Configuring the Cisco 1604 Router, 080355 BRI0 Attempting to dial

Chapter 3 Configuring the Cisco 1604 Router

Step 6—Testing the Cisco 1604 Connection to the Cisco AS5300

k.See 08:03:55.

The robo-austin PPP peer is successfully authenticated by the hq-sanjose peer. (BR0:1 CHAP: I SUCCESS id 5 len 4)

l.See 08:03:55.

MultiLink PPP uses a virtual-access interface to host the bundle. (BR0:1 PPP: Phase is VIRTUALIZED)

m.See 08:03:56.

LCP on Virtual-Access2 is forced up as it was already negotiated on the physical interface. For more information, enter the show interface virtual-access2 conf and debug vtemp commands. (%LINK-3-UPDOWN: Interface Virtual-Access2, changed state to up)

(Vi2 PPP: Phase is UP)

n.See 08:03:56.

IPCP negotiation begins.

(Vi2 IPCP: O CONFREQ [Closed] id 1 len 10)

(Vi2 IPCP: Address 10.1.254.4 (0x03060A01FE04))

o.See 08:03:56.

IP can now be used across this PPP connection. (Vi2 IPCP: I CONFACK [ACKsent] id 1 len 10) (Vi2 IPCP: State is Open)

p.See 08:03:57.

A route is installed to 10.1.254.1 to match the IP address negotiated by the peer. (BR0 IPCP: Install route to 10.1.254.1)

q.See 08:03:57 and 08:04:01.

The connection is made to hq-sanjose.

(Line protocol on Interface Virtual-Access2, changed state to up) (Interface BRI0:1 is now connected to 14085551234 hq-sanjose)

robo-austin#ping 10.1.254.1 Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.1.254.1, timeout is 2 seconds:

.!!!!

Success rate is 80 percent (4/5), round-trip min/avg/max = 116/182/372ms robo-austin#

08:03:55: BRI0: Dialing cause ip (s=10.1.254.4, d=10.1.254.1)

08:03:55: BRI0: Attempting to dial 14085551234

08:03:55: ISDN BR0: TX -> SETUP pd = 8 callref = 0x2F

08:03:55: Bearer Capability i = 0x8890

08:03:55: Channel ID i = 0x83

08:03:55: Keypad Facility i = '14085551234'

08:03:55: ISDN BR0: RX <- CALL_PROC pd = 8 callref = 0xAF

08:03:55: Channel ID i = 0x89

08:03:55: ISDN BR0: RX <- CONNECT pd = 8 callref = 0xAF

08:03:55: ISDN BR0: TX -> CONNECT_ACK pd = 8 callref = 0x2F

08:03:55: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up

08:03:55: BR0:1 PPP: Treating connection as a callout

08:03:55: BR0:1 PPP: Phase is ESTABLISHING, Active Open

08:03:55: BR0:1 PPP: No remote authentication for call-out

08:03:55: BR0:1 LCP: O CONFREQ [Closed] id 42 len 28

08:03:55: BR0:1 LCP: MagicNumber 0x623E5C69 (0x0506623E5C69)

08:03:55: BR0:1 LCP: MRRU 1524 (0x110405F4)

08:03:55: BR0:1 LCP: EndpointDisc 1 Local (0x130E01726F626F2D61757374696E)

08:03:55: BR0:1 LCP: I CONFREQ [REQsent] id 7 len 32

08:03:55: BR0:1 LCP: AuthProto CHAP (0x0305C22305)

08:03:55: BR0:1 LCP: MagicNumber 0xE16A73E6 (0x0506E16A73E6)

Cisco IOS Dial Services Quick Configuration Guide

3-18