Manuals / Cisco Systems / Computer Equipment / Network Router

Cisco Systems 806 manual Warnings, Before installing the router, read the following warnings

Models: 806

1 58

Download 58 pages 991 b

Page 22

Warnings

Chapter 2 Installation

Preparing for Installation

Warnings

Before installing the router, read the following warnings:

Warning Read the installation instructions before you connect the system to its power source.

Warning No operator serviceable parts inside. Refer servicing to qualified personnel.

Warning Before working on a chassis or working near power supplies, unplug the power cord on AC units; disconnect the power at the circuit breaker on DC units.

Warning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use.

Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240 VAC, 10A international) is used on the phase conductors (all current-carrying conductors).

Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals.

Warning The ports labeled "10BaseT", 100BaseTX", and "10/100" are safety extra-low voltage (SELV) circuits. SELV circuits should only be connected to other SELV circuits. Avoid connecting these circuits to telephone network voltage (TNV) circuits.

	Cisco 806 Router Hardware Installation Guide
2-2	78-10432-01

Image 22

Cisco Systems 806 manual Warnings, Before installing the router, read the following warnings

Contents

Corporate Headquarters Cisco 806 Router Hardware Installation GuideCustomer Order Number DOC-7810432= Text Part Number Turn the television or radio antenna until the interference stops Move the equipment farther away from the television or radioCisco 806 Router Hardware Installation Guide Copyright 2001, Cisco Systems, Inc All rights reservedPage Audience Contacting TAC by Using the Cisco TAC WebsitePreface World Wide WebTroubleshooting InstallationSafety Preparing for InstallationMaximum Cable Distances A-5 System Specifications A-1 Port Connector Pinouts A-2Cabling Specifications A-4 Ethernet Cable Specifications A-4 ContentsCisco 806 Router Hardware Installation Guide viiiContents 78-10432-01Audience PrefaceOrganization Conventions ¡Atención! Este símbolo de aviso significa peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y familiarizarse con los procedimientos estándar de prevención de accidentes World Wide Web Related DocumentationObtaining Documentation http//www-china.cisco.com http//www-europe.cisco.comDocumentation Feedback Documentation CD-ROMOrdering Documentation xiiiObtaining Technical Assistance Cisco.comTechnical Assistance Center Contacting TAC by Using the Cisco TAC WebsiteContacting TAC by Telephone Preface Obtaining Technical Assistance Cisco 806 Router Hardware Installation Guide78-10432-01 Product Overview FeaturesC H A P T E R Router Overview Front PanelFigure 1-2 Cisco 806 Back Panel Back PanelFigure 1-1 Cisco 806 Front Panel Chapter 1 Product Overview Router OverviewColor LEDsFunction Safety InstallationPreparing for Installation Preparing for Installation Preventing Router DamageWarnings Before installing the router, read the following warningsPreventing Electrostatic Discharge Damage Unpacking the Box Installing Your Router Preventing Router DamageConnecting Ethernet Devices Connecting a Hub Figure 2-2 Connecting a HubConnecting a Server, PC, or Workstation Figure 2-3 Connecting a Server, PC, or WorkstationConnecting to the Internet Connecting a Broadband ModemConnecting an Ethernet Switch Connecting a Terminal or PC to the Console Port2-10 Connecting the Power Supply 2-11Figure 2-7 Connecting the Power Supply Verifying Your Router Installation2-12 Desktop power supplyMounting on Table Mounting Your Router2-13 Mounting on Wall 2-142-15 The power supply must rest on a horizontal surface such as the floor or a table. If the power supply is not supported, it might place strain on the power supply cable and cause it to disconnect from the connector on the router back panelChapter 2 Installation Mounting Your Router 2-163. Place power supply Cisco 806 Router Hardware Installation Guide2-17 Where to Go from Herehttp//10.10.10.1 Cisco 806 Router Hardware Installation Guide 2-18Chapter 2 Installation Where to Go from Here 78-10432-01Before You Call Your Cisco Reseller TroubleshootingProblems During Initial Startup Problems After Router Is Running C H A P T E Rcorrectly, see Figure 2-4 or Figure 2-5 in Chapter Problems During Initial Startup“Installation.” Symptomsee Table 2-1 in Chapter 2, “Installation.” Problems After Router Is RunningTable 2-1 in Chapter 2, “Installation.” correctly, see Figure 2-2 or Figure 2-3 in ChapterSolutions SymptomProblem Table 3-2 Problems After Router is Running continuedSystem Specifications Specifications and CablesA P P E N D I X A Port Connector Pinouts Ethernet-See Table A-2, Table A-5, and Table A-6Table A-2 Cisco 806 Router Ethernet Connector Pinouts RJ-45 Table A-3 Console Connector Pinouts RJ-45Cabling Specifications Ethernet Cable SpecificationsAppendix A Specifications and Cables Cabling Specifications Maximum Cable DistancesTable A-5 Ethernet Cable Specifications Cisco 806 Router Hardware Installation GuideCisco 806 Router Hardware Installation Guide Appendix A Specifications and Cables Cabling Specifications78-10432-01 G L O S S A R Y NumericsGL-1 GL-2 GL-3 GL-4 IN-1 I N D ENumerics IN-2 IN-3 Index IN-4Cisco 806 Router Hardware Installation Guide 78-10432-01758 inches 19.35 cm Router Wall-Mount TemplateTo check scale 1 inch 2.54 cm