Cisco Systems ASR1002 1

32

Figure 14 Cisco ASR 1002 Router AC Power Cord

b. Take the power cord and run it below the handles of the power supply in slot 1 (the power supply you are connecting)

and the power supply in slot 0 (left) as shown in Figure 15. Make sure the power cord is hanging loosely so that it cannot

be disconnected from the AC power inlet.

Figure 15 Cisco ASR 1002 Router AC Power Cord - Left and Right

Caution Do not run the AC power cord through the power supply handles as shown in Figure 16.

Figure 16 AC Power Supply Cord Cabling for the Cisco ASR 1002 Router

1AC power cord and service loop

280383

OUTPUTINPUT

FAIL OK OK

FAN

This unit might have more than

one power supply connection.

All connections must be removed

to de-energize the unit.

1

280377

OUTPUTINPUT

FAIL OK OK

FAN

This unit might have more than

one power supply connection.

All connections must be removed

to de-energize the unit.

OUTPUTINPUT

FAIL OK OK

FAN

This unit might have more than

one power supply connection.

All connections must be removed

to de-energize the unit.

280378

OUTPUTINPUT

FAILOK OK

FAN

This unit might have more than

one power supply connection.

All connections must be removed

to de-energize the unit.

OUTPUTINPUT

FAIL OK OK

FAN

This unit might have more than

one power supply connection.

All connections must be removed

to de-energize the unit.

Contents

Main 1 Document Revision History Documentation Survey Obtaining Documentation and Submitting a Service Request Document Version Date Change Summary 2 Site Preparation and Unpacking Tools and Parts Prepare for Equipment Shelf or Tabletop Installation Prepare for Rack-Mount Installation 3 Attach the Rack-Mount BracketsChassis Front-Mounted 1 Front rack-mount bracket ear and holes 3 2 Attach the Rack-Mount BracketsChassis Rear-Mounted Four-Post Rack Installation 1 Rear rack-mount bracket ear and holes 3 2 1 Rear rack equipment rail 3 2 Rear rack-mount bracket ear and holes 4 Two-Post Rack Installation 1 Rack equipment rail 2 Attach the Cable-Management Bracket Chassis Ground Connection Installation 1 3 2 1 3 2 4 1 Chassis ground lug 3 2 Ground lug screws 4 4 Console and Auxiliary Port Cable Connections Figure 8 Cisco ASR 1002 Integrated Route Processor Console and Auxiliary Port Connectors SPA-4XOC3-POS STAT Management Ethernet Port Cable Connection Step 2 Insert the other end of the RJ-45 cable to your management device or network. Figure 9 Cisco ASR 1002 Integrated Route Processor Ethernet Management Port Connector 1 CONconsole port 2 1 Connect the Shared Port Adapter Cables Install the Cables Using the Cable-Management Bracket 1 2 3 4 5 1 BITS cable 4 2 MGMT cable 5 3 5 Connect AC Power to the Cisco ASR 1002 Router Connect DC Power to the Cisco ASR 1002 Router 41 5 63 8 7 LED Label LED Color Description 9 810 12 1 Chassis ESD socket 6 2 DC power supply slot 0 label 7 3 8 4 DC power supply LEDs 9 5 Fan 10 LED Label LED Color Description Page Verifying Power Supply operation Follow this procedure to verify power supply is operating correctly. Start the Cisco ASR 1002 Router LED Label LED Color In the Power Up State -Behavior Description LED Label LED Color Behavior Description Page 6 Using the Console to Access the CLI Configure Global Parameters Using the Set-up Facility Page Page Page Check the Running Configuration Settings Save the Running Configuration to NVRAM Perform Other Configuration Tasks 7 Power Off the Cisco ASR 1002 Router Replace the Cisco ASR1000-ESP5 or ASR1000-ESP10 Replace the Shared Port Adapters Replace a Power Supply in the Cisco ASR 1002 Router Removing an AC Power Supply Installing the AC Power Supply Figure 14 Cisco ASR 1002 Router AC Power Cord 1 Figure 16 AC Power Supply Cord Cabling for the Cisco ASR 1002 Router Figure 15 Cisco ASR 1002 Router AC Power Cord - Left and Right Caution Do not run the AC power cord through the power supply handles as shown in Figure 16. OUTPUTINPUT FAIL OK OK Removing the DC Power Supply Installing the DC Power Supply 1 Negative lead 3 2 1Ground lead wire 3Positive lead wire 2Negative lead wire 4DC power supply Standby switch