Cisco Systems ASR1002 2

3

2 Prepare for Installation

This section contains information about tools and parts, warnings, site preparation information, and information for

rack-mount and equipment shelf or tabletop installation.

Warning

Only trained and qualified personnel should install, replace, or service this equipment.

Statement 1030

Caution The eUSB panel door on the side of the Cisco ASR 1002 Router must not be opened. If there is a problem with

eUSB flash card, the chassis should be returned.

Before beginning this router installation, read the Regulatory Compliance and Safety Information for the Cisco ASR 1000 Series

Routers document.

Site Preparation and Unpacking

•Lift the router safely out of the packing container.

•Ensure the power service at the site is suitable for the router you are installing.

•Check the packing slip to ensure that all the proper components are present.

•Locate and have accessible the Site Log for recording information about this installation.

Tools and Parts

Use the following list of tools and parts as a checklist for preparing to install the Cisco ASR 1002 Router:

•ESD-preventative wrist strap

•AC power cord

•Appropriate cables to connect the router to the network and to the console terminal

•Tape measure and level (optional)

•Screwdrivers: Number 2 Phillips screwdriver and 3.5 mm or 3/16 inch flat-blade screwdriver

•Two chassis ground lugs and four screws

•The rack-mount and cable-management kit:

–

Four 19-inch rack-mount brackets (front and rear rails) and two cable-management brackets

–

Three sets of screws: one set for front rack-mount brackets (packaged with several black screws), another set for rear

rack-mount brackets (packaged with several screws), and a set for the cable-management brackets (packaged with four

screws).

Prepare for Equipment Shelf or Tabletop Installation

For an equipment shelf or tabletop installation, verify the following before installing the router:

•The router is off the floor and has adequate ventilation.

•An adequate chassis ground (earth) connection exists for the router.

•The router needs at last 3 inches (7.62 cm) of clearance at the inlet and exhaust vents (front and rear of router).

•The router needs 19 inches (48.26 cm) of clearance at the front and rear to allow for installation or to access cables or

equipment.

Contents

Main 1 Document Revision History Documentation Survey Obtaining Documentation and Submitting a Service Request Document Version Date Change Summary 2 Site Preparation and Unpacking Tools and Parts Prepare for Equipment Shelf or Tabletop Installation Prepare for Rack-Mount Installation 3 Attach the Rack-Mount BracketsChassis Front-Mounted 1 Front rack-mount bracket ear and holes 3 2 Attach the Rack-Mount BracketsChassis Rear-Mounted Four-Post Rack Installation 1 Rear rack-mount bracket ear and holes 3 2 1 Rear rack equipment rail 3 2 Rear rack-mount bracket ear and holes 4 Two-Post Rack Installation 1 Rack equipment rail 2 Attach the Cable-Management Bracket Chassis Ground Connection Installation 1 3 2 1 3 2 4 1 Chassis ground lug 3 2 Ground lug screws 4 4 Console and Auxiliary Port Cable Connections Figure 8 Cisco ASR 1002 Integrated Route Processor Console and Auxiliary Port Connectors SPA-4XOC3-POS STAT Management Ethernet Port Cable Connection Step 2 Insert the other end of the RJ-45 cable to your management device or network. Figure 9 Cisco ASR 1002 Integrated Route Processor Ethernet Management Port Connector 1 CONconsole port 2 1 Connect the Shared Port Adapter Cables Install the Cables Using the Cable-Management Bracket 1 2 3 4 5 1 BITS cable 4 2 MGMT cable 5 3 5 Connect AC Power to the Cisco ASR 1002 Router Connect DC Power to the Cisco ASR 1002 Router 41 5 63 8 7 LED Label LED Color Description 9 810 12 1 Chassis ESD socket 6 2 DC power supply slot 0 label 7 3 8 4 DC power supply LEDs 9 5 Fan 10 LED Label LED Color Description Page Verifying Power Supply operation Follow this procedure to verify power supply is operating correctly. Start the Cisco ASR 1002 Router LED Label LED Color In the Power Up State -Behavior Description LED Label LED Color Behavior Description Page 6 Using the Console to Access the CLI Configure Global Parameters Using the Set-up Facility Page Page Page Check the Running Configuration Settings Save the Running Configuration to NVRAM Perform Other Configuration Tasks 7 Power Off the Cisco ASR 1002 Router Replace the Cisco ASR1000-ESP5 or ASR1000-ESP10 Replace the Shared Port Adapters Replace a Power Supply in the Cisco ASR 1002 Router Removing an AC Power Supply Installing the AC Power Supply Figure 14 Cisco ASR 1002 Router AC Power Cord 1 Figure 16 AC Power Supply Cord Cabling for the Cisco ASR 1002 Router Figure 15 Cisco ASR 1002 Router AC Power Cord - Left and Right Caution Do not run the AC power cord through the power supply handles as shown in Figure 16. OUTPUTINPUT FAIL OK OK Removing the DC Power Supply Installing the DC Power Supply 1 Negative lead 3 2 1Ground lead wire 3Positive lead wire 2Negative lead wire 4DC power supply Standby switch