Manuals / Cisco Systems / Computer Equipment / Network Card

Cisco Systems Gateway 10 quick start Site Preparation

Models: Gateway 10

1 40

Download 40 pages 53.37 Kb

Page 4

2Site Preparation

Do not unpack the chassis until you are ready to install it. Keep the chassis in the shipping container to prevent accidental damage until you determine an installation site.

Before you install the Cisco RFGW-10, review the following:

•The environmental conditions your installation site must meet to maintain normal operation.

•The power requirements that must be in place at your installation site.

•The cabling requirements for your installation site.

•Rack-mounting requirements.

•The equipment required to install the Cisco RFGW-10 UEQAM.

For more details on site preparation, refer to “Preparing Your Site for Installation” chapter in the Cisco RF Gateway 10 Hardware Installation Guide.

4

Image 4

Cisco Systems Gateway 10 quick start Site Preparation

Contents

1 Overview 2 Site Preparation 3 Chassis Installation 4 Connecting Cables 5 Powering on the Cisco RF Gateway6 Configuring the Cisco RF Gateway 10 at Startup 7 Troubleshooting 8 Obtaining Documentation and Submitting a Service RequestCisco RF Gateway 10 Components 1 Overviewthis equipment. Statement Fan assembly RF Switch Cards/Coaxial cable termination slotsUniversal RF line card slots Supervisor card slots2 Site Preparation Installation Methods 3 Chassis InstallationGeneral Rack Installation Guidelines Verifying Rack Dimensions CharacteristicRack-mounting a Cisco RFGW-10 UEQAM DescriptionInstalling the Chassis Installation Brackets Installing the Chassis Installation Handles Figure 3 Chassis Installation BracketChassis Front Rack-mount Brackets Installation Attaching the Chassis Rack-mount BracketsChassis Mid-Mounted Rack-Mount Bracket Installation Installing the Cisco RFGW-10 UEQAM in a Rack component at the bottom of the rack rack. StatementFigure 8 Positioning the Chassis on the Chassis Installation Bracket Figure 9 Positioning the Chassis on the Rack Fan tray handleTwo-Post Rack Installation Mid-Mounted Figure 10 Securing the Side Rack-Mount BracketsFigure 11 Installing the Cisco RFGW-10 in a Two-Post Equipment Rack Connecting the Chassis to Ground you are uncertain that suitable grounding is available. StatementRecommended Tools and Supplies QuantityComments Description4 Connecting Cables Power and Ground ConnectionsConnect the Console and Management Ports Console PortCabling the Cisco RFGW-10 UEQAM Management PortFigure 15 5-Bundle Quad-Shielded Cable with MCX Connectors Part NumbersTable 3 Part Numbers Nominal Attenuation Part NumbersdB/100 ft DescriptionInstalling the UCH on the Cisco RFGW-10 UEQAM RF Switch Card Installing or Replacing the Cables in the UCH2 Figure 18 Installing the UCH on the FaceplateInstalling Cables RF Switch Line Card PortRF Switch User Defined Tools and EquipmentFigure 19 Removing an ESD Cap from a MCX connector Figure 20 Removing an ESD Cap from an F connectorFigure 21 Placing Cables in the UCH2 155824Troubleshooting the RF Switch Card Installation Connecting the DTI ConnectionsVerifying External DC Power Source Connections 5 Powering on the Cisco RF GatewayVerifying Basic System Power DC PEM captive screws 6 Configuring the Cisco RF Gateway 10 at Startup Entering the Initial Configuration InformationBasic Configuration Using the Setup Facility System Configuration DialogUsing Configuration Mode to Configure Your Switch Configuring a Default GatewayConfiguring a Static Route Controlling Access to Privileged EXEC CommandsSetting or Changing a Static Enable Password Using the enable password and enable secret CommandsConfiguring FastEthernet1 Port Setting or Changing a Privileged PasswordBefore You Call for Technical Assistance 7 TroubleshootingVerifying Normal Startup Sequence 8 Obtaining Documentation and Submitting a Service Request 9 Related Documents Cisco RF Gateway 10 Command Reference GuidePage Americas Headquarters Asia Pacific HeadquartersEurope Headquarters Cisco Systems, Inc