Cisco Systems OL-9392-04 manual Port 10BASE-FL Ethernet Switching Module WS-X6024-10FL-MT

Chapter 2 Ethernet and Gigabit Ethernet Switching Modules

10/100 and 10/100/1000 Ethernet Switching Modules

24-Port 10BASE-FL Ethernet Switching Module (WS-X6024-10FL-MT)

The 24-port 10BASE-FL switching module (WS-X6024-10FL-MT) provides 24 switched, 10-Mbps, full- or half-duplex ports. (See Figure 2-1.) The module has 24 MT-RJ connectors for connection to multimode fiber-optic (MMF) cable.

The QoS port architecture (Rx/Tx) for this module is 1q4t/2q2t.

Note This module is a Class 1 laser product. Refer to the Regulatory Compliance and Safety Information for the Cisco 7600 Series Routers for information on working with lasers.

Figure 2-1 24-Port 10BASE-FL Ethernet Switching Module (WS-X6024-10FL-MT)

WS-X6024-10FL-MT

S

TU

TA

S

K

K

K

IN

K

IN

K

IN

K

K

K

K

IN

K

IN

K

IN

K

IN

K

IN

K

IN

K

K

K

K

K

K

IN

K

IN

K

IN

K

K

24 PORT 10FL

IN

IN

IN

IN

IN

IN

IN

IN

IN

IN

IN

IN

L

L

L

L

L

L

L

L

L

L

L

L

L

L

L

L

L

L

L

L

L

L

L

L

26947

The front panel LEDs are described in Table 2-3 on page 2-21.

48-Port 10/100/1000BASE-T Ethernet Switching Module (WS-X6148-GE-TX)

The 48-port 10/100/1000BASE-T switching module (WS-X6148-GE-TX) provides 48 switched, 10/100/1000-Mbps autosensing, full- or half-duplex ports. (See Figure 2-2.) The module has 48 RJ-45 connectors for use with either Category 3, Category 5, Category 5e, or Category 6 UTP cable. This module can be upgraded with an inline-power daughter card to support IP phones.

Figure 2-2 48-Port 10/100/1000BASE-T Ethernet Switching Module (WS-X6148-GE-TX)

WS-X6148V-GE-TX 1											11
2											12
STATUS
1	2	3	4	5	6	7	8	9	10	11	12

13	23
14	24
48 PORT	10/100/1000

13 14 15 16 17 18 19 20 21 22 23 24 BASE-T GE

25											35	37													47
26											36	38													48
												SWITCHING MODULE													PHONE	90851
25	26	27	28	29	30	31	32	33	34	35	36		37	38	39	40	41	42	43	44	45	46	47	48

The front panel LEDs are described in Table 2-3 on page 2-21.

48-Port 10/100/1000BASE-T Ethernet Switching Module (WS-X6148V-GE-TX)

The 48-port 10/100/1000BASE-T switching module (WS-X6148V-GE-TX) provides 48 switched, 10/100/1000-Mbps autosensing, full- or half-duplex ports. (See Figure 2-3.) The module has 48 RJ-45 connectors for use with either Category 3, Category 5, Category 5e, or Category 6 UTP cable. The “V” in the product number indicates that the inline-power daughter card is installed on the module. With the voice daughter card installed, the module provides these IP phone features on each port:

•Inline power—Provides 48 VDC over standard Category 5, Category 5e, or Category 6 UTP cable up to 328 feet (100 meters) from the switch to the IP phone. With inline power, pairs 2 and 3 (pins 1, 2, 3, and 6) of the four pairs in the cable are used to transmit power (6.3 W) from the switch. This method of supplying power is sometimes called phantom power because the power signals travel over the same two pairs used to transmit Ethernet signals. The power signals are completely transparent to the Ethernet signals and do not interfere with their operation.

Cisco 7600 Series Routers Module Guide

2-4 OL-9392-04