Printer Operation
Mode Settings
Top Menu | Sub Menu | Default | Menu | Remarks | |
Interfaces | 9600 | 115200 | Setting the baud rate of the serial interface. | ||
|
|
| 57600 | • All settings related to the interface are | |
|
|
| 38400 | enabled after the power is reconnected. | |
|
|
| 19200 |
| |
|
|
| 9600 |
| |
|
|
| 4800 |
| |
|
|
| 2400 |
| |
| None | None | Setting the communication parity for the | ||
|
|
| Odd | serial interface. | |
|
|
| Even |
| |
|
|
|
|
| |
| 8 bits | 8 bits | Setting the character length for the serial | ||
|
|
| 7 bits | interface. | |
|
|
|
|
| |
| 1 bit | 1 bit | Setting the stop bit for the serial interface. | ||
|
| 2 bits |
| ||
|
|
|
|
| |
| On Yes | On Yes | Selectively setting the | ||
|
|
| Off No | the serial interface. | |
|
|
|
|
| |
| IEEE1284 | On | On | Setting both direction of the Centro | |
|
|
| Off | Interface. | |
|
|
|
|
| |
Machine | Model Number | – | Displays the model name. | ||
Information |
|
|
|
| |
Boot Version | – | *.* | Displays the boot version. | ||
[Machine Info] | |||||
|
|
|
| ||
ROM Version | – | ******** | Displays the ROM version. | ||
| |||||
|
|
|
|
| |
| ROM Date | – | **/**/** | Displays the date the ROM was prepared. | |
|
|
|
|
| |
| ROM CheckSum | – | **** | Displays the check sum of the ROM. | |
|
|
|
|
| |
| Head Check | – | OK | Displays the results of the head check. | |
|
|
| NG |
| |
|
|
|
|
| |
| Print Counter | – | ****.*** km | Displays the print counter. | |
|
|
|
|
| |
| Service Counter | – | ****.*** km | Displays the service counter. | |
|
|
|
|
| |
| Sensor Monitor | – | *.* V | Displays the sensor level. | |
|
|
|
|
| |
| Option Interface | – | None | Displays the presence/absence of the | |
| [Option I/F] |
| LAN | optional interface. | |
|
|
|
|
| |
Test Mode | Print Pattern | Current Config | Current Config | Executes the test pattern. | |
|
|
| Global Config |
| |
|
|
| Sample |
| |
|
|
|
|
| |
| Head Check | No | Yes | Executes head check. | |
|
|
| No |
| |
|
|
|
|
| |
| Factory Default | No | Yes | Initializes the set values of the configuration | |
|
|
| No | set to the state when the unit was shipped | |
|
|
|
| from the factory. | |
|
|
|
|
| |
| Hex Dump | No | Yes | Sets the hex dump mode. | |
|
|
| No |
| |
|
|
|
|
| |
| Serial Monitor | – | – | Displays the state of the serial interface. | |
|
|
|
|
| |
| Auto Calibration | See Through | See Through | Executes the calibration of the sensor. | |
| [Auto Cal] |
| Reflect |
| |
|
|
|
|
| |
| Sensor Monitor | See Through | See Through | Displays the level of the sensor. | |
|
|
| Reflect |
| |
|
|
|
|
| |
Global | – | Config Set 1 | Config Set 1 | Sets the Config Set. | |
configuration |
|
| Config Set 2 |
| |
[Global Config] |
|
| Config Set 3 |
|
Note: To restore factory default settings, turn on printer power while pushing the MENU and PAUSE keys simultaneously, then press the FEED key and the STOP key sequentially.
39