Manuals / Citizen Systems / Computer Equipment / Printer

Citizen Systems CMP-10 manual Appendix Handling Belt Clip Kit, How to Mount Belt Clip

Models: CMP-10

1 40

Download 40 pages 54.86 Kb

Page 36

8. APPENDIX HANDLING BELT CLIP KIT

8. APPENDIX HANDLING BELT CLIP KIT

This kit consists of a belt clip, two screws, and two rubber feet.

8.1 How to Mount Belt Clip

Peel off the cover seal in the square frame at the bottom of the CMP-10 carefully.

Mount the belt clip in the square frame using the two screws supplied. The direction of the belt clip should be as per the drawing below.

Note: Do not use screws without mounting the belt clip. The screws when mounted alone reach too deep and may come in contact with the internal circuit board and cause a failure.

8.2 Mounting Rubber Feet

Confirm that the grooves for the rubber feet are clean and neither dust nor oil is present on the grooves for rubber feet.

Peel off the liner sheet of the adhesive seal for rubber foot and carefully fit the rubber foot to the groove. Press and hold to secure the rubber foot.

Belt clip

Grooves for rubber feet

— 32 —

Image 36

Citizen Systems CMP-10 manual Appendix Handling Belt Clip Kit, How to Mount Belt Clip, Mounting Rubber Feet

Contents

MOBILE THERMAL PRINTER FCC Declaration of Conformity Compliance Statements FCC Compliance Statement for American UsersEMI Compliance Statement for Canadian Users CE Declaration of Conformity EN61000-3-2 1995+A1 1998+A2 1998+A14 20αGENERAL PRECAUTIONS SAFETY PRECAUTIONS About PictogramDefinition of Pictogram DangerPrecautions in Handling Printer Precautions on Using Printer Precautions on Using Battery DANGERPrecautions on Setting Print Paper Carry used battery in recycling agentNGNG Precautions on Using Thermal Paper Print Paper Precautions on Using Special Serial Cable Precautions on Using AC AdapterTHE TABLE OF CONTENTS LIST OF COMMANDSMAINTENANCE AND SERVICE GENERAL SPECIFICATIONS1.1 Features 1. INTRODUCTION1.2 Included and Optional Accessories 1.3 Type ClassificationCMP - 10 - U 5 M 2. GENERAL SPECIFICATIONS FeatureParameters Feature ParametersFeature ParametersReliability 3.1 LED Indicators 3. EXPLANATION OF PRINTER PARTS3.2 Communication Port and Switch 3.3 Inside of Paper Cover 3.4 BuzzerWhen magnetic card was successfully read sounds once 10 Paper feed roller Feeds paper through the printing mechanism3.5 Bottom Surface and Battery Cover 3.6 Dimensions and Views Unit mm DC Jack4. OPERATION 4.1 Replacing the Paper Roll4.2 Method of Charging 4.3 Communication by IrDA The IrDA beam4.4 Communication Via Serial Port Cable Rubber projectionSerial port cover Lift and open the serial port cover Insert serial cableTo read the mag stripe card, it is necessary to send a special command to the printer 4.6 Removing the Battery Pack 4.7 Installing the Battery Pack 5.1 Auto Power OFF 5.3 Low Battery Detection5. FUNCTION 5.2 Interface Selection5.5 Self Testing and Internal Settings 5.4 Monitoring the Print Head Overheating5.6 Print Area 6. LIST OF COMMANDS Enabling/disabling the panel switches Setting the time interval for automatic Power OFFSpecifying/canceling the inverted characters Setting printer flags7. MAINTENANCE AND SERVICE Northern AmericaOther Areas 8.1 How to Mount Belt Clip 8. APPENDIX HANDLING BELT CLIP KIT8.2 Mounting Rubber Feet MEMO MEMO MEMO 0201E-0212 Printed in Korea Information Systems Division CBM Bldg., 5-68-10, Nakano, Nakano-kuTokyo 164-0001, Japan Tel +81-3 5345-7540 Fax +81-3