Manuals / Citizen Systems / Computer Equipment / Printer

Citizen Systems CMP-10 Communication Via Serial Port Cable, Rubber projection, Serial port cover

Models: CMP-10

1 40

Download 40 pages 54.86 Kb

Page 27

4.4 Communication Via Serial Port (Cable)

4.4 Communication Via Serial Port (Cable)

For communication with RS-232C, prepare dedicated serial cable. Open the serial port cover and while holding the connector with the wording marked “Push” faciing upward, insert the connector into the serial port.

Here, hold the connector with the surface marked “Push” down. Connect the other end of the cable of the cable to the device to be connected.

To disconnect the connector, securely do it while pressing the portion marked “Push”.

This part is fixed to the body; therefore, it cannot be detached as shown in the figure.

Rubber projection

Serial port cover

Lift and open the serial port cover.

Insert serial cable:

To replace the serial port cover, press in the rubber packing till the cover seats firmly.

CAUTION!

If the cable is connected with Power ON, turn the Power OFF once and then turn the Power ON again to activate the connection with serial cable.

Set the flow control setting of the device to be connected to Xon/Xoff. In case of hardware control (DTR/DSR control), the Power switch may become disabled.

— 23 —

Image 27

Citizen Systems CMP-10 manual Communication Via Serial Port Cable, Rubber projection, Serial port cover

Contents

MOBILE THERMAL PRINTER FCC Declaration of Conformity Compliance Statements FCC Compliance Statement for American UsersEMI Compliance Statement for Canadian Users EN61000-3-2 1995+A1 1998+A2 1998+A14 20α CE Declaration of ConformityGENERAL PRECAUTIONS Danger SAFETY PRECAUTIONSAbout Pictogram Definition of PictogramPrecautions in Handling Printer Precautions on Using Printer DANGER Precautions on Using BatteryPrecautions on Setting Print Paper Carry used battery in recycling agentNGNG Precautions on Using Thermal Paper Print Paper Precautions on Using AC Adapter Precautions on Using Special Serial CableGENERAL SPECIFICATIONS THE TABLE OF CONTENTSLIST OF COMMANDS MAINTENANCE AND SERVICE1. INTRODUCTION 1.1 Features1.2 Included and Optional Accessories 1.3 Type ClassificationCMP - 10 - U 5 M 2. GENERAL SPECIFICATIONS FeatureParameters Parameters FeatureFeature ParametersReliability 3. EXPLANATION OF PRINTER PARTS 3.1 LED Indicators3.2 Communication Port and Switch 10 Paper feed roller Feeds paper through the printing mechanism 3.3 Inside of Paper Cover3.4 Buzzer When magnetic card was successfully read sounds once3.5 Bottom Surface and Battery Cover Unit mm DC Jack 3.6 Dimensions and Views4.1 Replacing the Paper Roll 4. OPERATION4.2 Method of Charging The IrDA beam 4.3 Communication by IrDALift and open the serial port cover Insert serial cable 4.4 Communication Via Serial Port CableRubber projection Serial port coverTo read the mag stripe card, it is necessary to send a special command to the printer 4.6 Removing the Battery Pack 4.7 Installing the Battery Pack 5.2 Interface Selection 5.1 Auto Power OFF5.3 Low Battery Detection 5. FUNCTION5.5 Self Testing and Internal Settings 5.4 Monitoring the Print Head Overheating5.6 Print Area 6. LIST OF COMMANDS Setting printer flags Enabling/disabling the panel switchesSetting the time interval for automatic Power OFF Specifying/canceling the inverted characters7. MAINTENANCE AND SERVICE Northern AmericaOther Areas 8.1 How to Mount Belt Clip 8. APPENDIX HANDLING BELT CLIP KIT8.2 Mounting Rubber Feet MEMO MEMO MEMO 0201E-0212 Printed in Korea Information Systems Division CBM Bldg., 5-68-10, Nakano, Nakano-kuTokyo 164-0001, Japan Tel +81-3 5345-7540 Fax +81-3