Manuals / Cleveland Range / Kitchen Appliance / Oven

Cleveland Range Steam Oven installation manual Pc-Haccp Kit Contents, Photo

Models: Steam Oven

1 30

Download 30 pages 6.89 Kb

Page 2

Read and understand this manual before using this PC-HACCP Kit.

CAUTION

Read and understand this manual before using this PC-HACCP Kit.

Follow all Safety and Operating Instructions

Failure to do so can result in injury, and equipment and property damage.

NOTICE: In addition to the kit, the following wire is required for installation between each oven:

•For standard voltage units: 18/ 2 CPM/CL3P audio wire – e.g.: McMaster-Carr P/N- 71055K76.

•For 480 volt units use 18/2 UL AWM 2501 communication wire – e.g.: Allied Electronics P/N – 708-1301. (Can be used with all voltage ovens.)

PC–HACCP KIT CONTENTS

6

5

1

4

Photo 1

2

3

1 Software-CD - 300550

2 Network Connection Cable – 300551 (included only w/ 232 kit)

3 Dongle - C5009210

4 PC Interface Converter - C5009156 (included only w/ 232 kit)

5 9 Volt Power Supply for Converter – 300548 (included only w/ 232 kit) 6 Operating Instructions – 260AZV

USB TO RS 232/485 ADAPTER 300555 included only with kit number CPC-HACCP-MUUSB

USB Cable

USB Adapter

Software-CD

See Page 20 for

Installation Instructions

Photo 2

2

Image 2

Cleveland Range Steam Oven Pc-Haccp Kit Contents, Read and understand this manual before using this PC-HACCP Kit, Photo

Contents

FOR RS232 connection use part number CPC-HACCP-MU232 Turn off all power to Combis before installation of PC-HACCP NetworkFollow all Safety and Operating Instructions FOR USB connection use part number CPC-HACCP-MUUSBPhoto PC-HACCP KIT CONTENTSRead and understand this manual before using this PC-HACCP Kit Follow all Safety and Operating Instructions5, 6 4,7 1 Electronic Board 1 - C5019104 2 Connector 1 - C5002091RS485 Communication Module p/n C-RS485 3 Bracket with Studs 1 - C2114799TO CONNECT THE RS232 CONVERTER TO THE PC Photo Photo Photo PhotoRS232 CABLE CONNECTION FOR CONVERTER TO RS485 ONLY The PC Converter wiring is connected to the FIRST Combi in the ChainA RED WIRE B BLACK WIRE GROUND GROUND OR SHIELD WIRE Photo 8 shows the cable connections for the PC ConverterNote the position of the Dongle on the PC in Photo From the bottom edge of the side panel, push up and pull out Remove the Control Side CoverTurn the 1/4 turn quick-locks to loosen Remove the side panel and set it asideRemove the Control Panel Attaching the Base Plate to the Communication Module Photo Attaching the Base Plate to the Communication ModulePhoto PhotoRemove the sanitary seal plug from the underside of the Combi attaching the wires to the network boardsInserting the Communication Module Cable into the Oven Insert the new bushing, P/N 111751 into the openingConnect the Network Cable to the Communication Module Setting the Jumpers on the Communication Module Photomoving parts Secure cable to the upper right spacer as shown in PhotoPlace Control Board and Module back into the Combi Board and cables are attachedPhoto Replace the Operation PanelRemount the Operation Panel back into the Combi PhotoPush up and in from the bottom edge of the side panel See the PC-HACCP Instructions to use the PC-HACCP NetworkReplace the Control Side Panel Turn the 1/4 turn quick-locks to tightenDirections for Installing the USB Adapter Select install from a list of specific location advanced Ignore this screen if it appearsUncheck “Include this location in the search.” Click Next. Let search The Hardware wizard will appear a second time Follow the directions in each screen Allow search for CD Click Finish to close the screen Configure your serial device 1. Right click My Computer, select propertiesExpand the Ports COM & LPT device Right click on the “USB Serial Port COM??” item Page Page For USB to RS232 Switches 2, 3, 4 are ON For USB to RS485 Switches 1 and 4 are ONPlace connect jumper #1 Jumper #1 Position Rev Page This Page for Internal Record Only, Not for Printing116 March Cleveland Range, LLC