Lighting Main Burners
Fryer Burner Lighting
Igniter Lighting
1. Turn on any or all main burner gas control knobs to high. (Fig. 19) |
Igniter Lighting:
24b
2. | Press the igniter switch until the flame ignites. |
3. | If the flame does not immediately light, turn off control knobs and |
| wait five minutes for gas to clear. |
4. | Repeat steps 1 through 3. |
5. | If the burner does not light on second try, turn off knobs and |
| try |
Match Lighting
CAUTION
Use a LONG wooden match. Make sure all burner controls are off except one being lighted. If a
1.Strike and place the burning match near the BURNER being operated.
2.Turn on BURNER CONTROL KNOB while holding match near burner.
3.The other burners can be ignited by turning them on one at a time after first burner is lighted.
Lighting Rotisserie Burner
CAUTION
•DO NOT OPERATE THE GRILL WITH THE ROTISSERIE HANDLE ON THE SPIT ROD.
Igniter Lighting
1.Turn on Rotisserie Burner Gas Control knob to high. (Fig. 19)
2.Press the igniter switch until the flame ignites.
3.If the flame doesn’t immediately light, turn off control knob and wait five minutes for gas to clear.
4.Repeat steps 1 through 3.
5.If the burner does not light on second try, turn off knob and try
Match Lighting
CAUTION
Use a LONG wooden match. Make sure all burner controls are off except one being lighted. Strike the match, and place the burning match near the burner screen beside the electrode tip.
1.Strike and place the burning match near the ROTISSERIE BURNER SCREEN.
2.Turn on ROTISSERIE BURNER CONTROL KNOB while holding match near the burner screen.
CAUTION
•Before removing spit from grill, make sure gas control knobs are turned to “OFF”. Use protec- tive gloves or tools when removing the spit to avoid burn hazard from spit, food or hot juices.
38
1.Make sure all valves or OFF.
2.Turn on the cylinder valve.
3.Push in and turn on the Fryer Control Knob counterclockwise to START. (Fig. 24b).
4.Continue to depress and hold
the Fryer Control Knob.
5.Press the igniter switch until the flame ignites.
6. After burner ignition, continue to hold Fryer Control Knob in for
7.If the flame does not immediately light, turn off Fryer Control Knob and wait for five minutes for gas to clear.
8.Repeat steps 3 through 6.
9.If the burner does not light after trying again, turn off Fryer Control Knob and try match lighting the burner.
HINT: If the igniter fails to light the fryer burner, adjust electrode tip with
Match Lighting
CAUTION
Use a LONG wooden match. Make sure all burner controls are off except one being lighted. Strike the match and place the burning match near the burner gas port holes, from below the fryer. Removing the Fryer Grease Pan will make it easier to access the Fryer Burner. Be sure to replace the Fryer Grease Pan as soon as the burner stays lit.
1.Make sure all valves or OFF.
2.Turn on the cylinder valve.
3.Strike and place the burning match near the burner gas port holes, from below the fryer.
4.Push in and turn on the Fryer Control Knob counterclockwise to START. (Fig. 24b).
5.Continue to depress and hold the Fryer Control Knob.
6.After burner ignition, continue to hold Fryer Control Knob in for 15-
30seconds then rotate Fryer Control Knob to HIGH setting.
Shutting Off the Grill
CAUTION
DO NOT touch hot grill parts with bare hands! You MUST use protective gloves.
1.Turn all burner control knob(s) to off.
2.After burner flame goes out, turn off fuel supply. For an L.P. cylinder, turn the L.P. cylinder knob in a clockwise direction until it stops.
CAUTION
Be certain the gas is shut off at the L.P. cylinder valve anytime the grill is not in use.
