Compaq 9900 - page 112

98 Chapter 5

Planning for Installation and Operation

Floor cutout area for cables

Caster

Screw jack

Service clearance

GGrid panel (over 17.7" × 17.7" )

Opening on the bottom of the f rame

(for external cable entry )

(Unit : inches)

31.5"

9.8" *2

9.8" *2

94.5"

26.8"

2.4"

2.4"

4.6"

4.6"

22.2"

Front

6.9" *2 6.9"

*2

3.4"

3.4" 22.75"

0.6"

0.6" 28.3"

6.5"

6.5" 16.5"

29.5"

31.5"

31.5"

G

G

11"

23.5"

3" 3"

3.9"

10"

Recommended value: 15.75"

( 11.8" - 22.4" ) *1

Recommended value: 11.8"

( 9.8" - 15.75" ) *1

*1: Values in parentheses show allowable range of the floor cutout dimension. The floor cutout should be planned in the cent er

of the DKC. In case that the floor cutout is planned in a right position for the external cable work and it is within the allowable

range, the cutout position may be off-center. In this case, check the relation between the positions of the cutout and the opening

on the bottom of the frame. If the floor cutout width is planned more than 520 mm, be careful about the restriction of the movable

direction because there is a possibility that the caster wheels fall down into the cutout.

*2: These dimensions vary with the floor cutout dimension.

Figure 5.15 9960 Controller Frame Service Clearance and Cutouts (inches)

Contents

Main Page 2003 Hitachi Data Systems Corporation, ALL RIGHTS RESERVED Trademarks Notice of Export Controls Document Revision Level Source Documents for this Revision Changes in this Revision Preface Microcode Level Thank you! COMMENTS Page Contents Page Page Page List of Figures List of Tables Page Page Chapter 1 Overview of the Lightning 9900 Subsystem 1.1 Key Features of the Lightning 9900 Subsystem 1.1.1 Continuous Data Availability 1.1.2 Connectivity 1.1.3 S/390 Compatibility and Functionality 1.1.4 Open-Systems Compatibility and Functionality 1.1.5 Hitachi Freedom NAS and Hitachi Freedom SAN Page 6 Chapter 1 Overview of the Lightning 9900 Subsystem 1.1.6 Program Products and Service Offerings Hitachi Lightning 9900 User and Reference Guide 7 Table 1.1 Program Products and Service Offerings (continued) 1.1.7 Subsystem Scalability 1.2 Reliability, Availability, and Serviceability Page Chapter 2 Subsystem Architecture and Components 2.1 Overview Page Page 2.2 Components of the Controller Frame 2.2.1 Storage Clusters 2.2.2 Nonvolatile Shared Memory 2.2.3 Nonvolatile Duplex Cache 2.2.4 Multiple Data and Control Paths 2.2.5 Redundant Power Supplies 2.2.6 Client-Host Interface Processors (CHIPs) and Channels Hitachi Lightning 9900 User and Reference Guide 17 Table 2.1 CHIP and Channel Specifications 2.2.7 Channels 2.2.8 Array Control Processors (ACPs) 20 Chapter 2 Subsystem Architecture and Components Table 2.2 ACP Specifications 2.3 Array Frame Page 2.3.1 Disk Array Groups 2.3.2 Sequential Data Striping 2.4 Intermix Configurations 2.4.1 RAID-1 & RAID-5 Intermix 2.4.2 Hard Disk Drive Intermix 2.4.3 Device Emulation Intermix 2.5 Service Processor (SVP) 2.6 Remote Console PC Page Chapter 3 Functional and Operational Characteristics 3.1 New 9900 Features and Capabilities 3.2 I/O Operations 3.3 Cache Management 3.3.1 Algorithms for Cache Control 3.3.2 Write Pending Rate 3.4 Control Unit (CU) Images, LVIs, and LUs 3.4.1 CU Images 3.4.2 Logical Volume Image (LVIs) 3.4.3 Logical Unit (LU) Type 3.5 System Option Modes Hitachi Lightning 9900 User and Reference Guide 33 Table 3.4 System Option Modes for Open-System Connectivity 34 Chapter 3 Functional and Operational Characteristics Table 3.5 System Option Modes for ShadowImage - S/390 and ShadowImage Hitachi Lightning 9900 User and Reference Guide 35 Table 3.6 System Option Modes for TrueCopy - S/390 Synchronous & Asynchronous (continued) 36 Chapter 3 Functional and Operational Characteristics Table 3.7 System Option Modes for HXRC Table 3.8 System Option Modes for Concurrent Copy (CC) 3.6 Open Systems Features and Functions 3.6.1 Failover and SNMP Support 3.6.2 Share-Everything Architecture 3.6.3 SCSI Extended Copy Command Support 38 Chapter 3 3.7 Data Management Functions Hitachi Lightning 9900 User and Reference Guide 39 Table 3.10 Data Management Functions for S/390 Users 3.7.1 Hitachi TrueCopy (TC) 3.7.2 Hitachi TrueCopy S/390 (TC390) 3.7.3 Hitachi ShadowImage (SI) 3.7.4 Hitachi ShadowImage S/390 (SI390) 3.7.5 Command Control Interface (CCI) 3.7.6 Extended Copy Manager (ECM) 3.7.7 Hitachi Extended Remote Copy (HXRC) 3.7.8 Hitachi NanoCopy 3.7.9 Data Migration 3.7.10 Hitachi RapidXchange (HRX) 3.7.11 Hitachi Multiplatform Backup/Restore (HMBR) 3.7.12 HARBOR File-Level Backup/Restore 3.7.13 HARBOR File Transfer 3.7.14 HiCommand 3.7.15 LUN Manager 3.7.16 LU Size Expansion (LUSE) 3.7.17 Virtual LVI/LUN 3.7.18 FlashAccess 3.7.19 Cache Manager 3.7.20 Hitachi SANtinel 3.7.21 Hitachi SANtinel S/390 3.7.22 Prioritized Port and WWN Control (PPC) 3.7.23 Hitachi Parallel Access Volume (HPAV) 3.7.24 Dynamic Link Manager (DLM) 3.7.25 LDEV Guard 3.7.26 Hitachi CruiseControl 3.7.27 Hitachi Graph-Track Chapter 4 Configuring and Using the 9900 Subsystem 4.1 S/390 Configuration 4.1.1 Subsystem IDs (SSIDs) 4.2 S/390 Hardware Definition 4.2.1 Hardware Definition Using IOCP (MVS, VM, or VSE) Hitachi Lightning 9900 User and Reference Guide 55 Figure 4.1 IOCP Definition for FICON Channels (direct connect and via FICON switch) Page Page Page 4.2.2 Hardware Definition Using HCD (MVS/ESA) Page Page Configuring and Using the 9900 Subsystem 62 Chapter 4 Figure 4.5 Basic HCD Panel (Step 2) Figure 4.6 Define, Modify, or View Configuration Data (Step 3) Hitachi Lightning 9900 User and Reference Guide 63 Figure 4.7 Control Unit List Panel (Step 4) Figure 4.8 Add Control Unit Panel (Step 5) Configuring and Using the 9900 Subsystem 64 Chapter 4 Figure 4.9 Selecting the Operating System (Step 6) Figure 4.10 Control Unit Chpid, CUADD, and Device Address Range Addressing (Step 7) Hitachi Lightning 9900 User and Reference Guide 65 Figure 4.11 Select Processor / Control Unit Panel (Step 8) Figure 4.12 Control Unit List (Step 9) Configuring and Using the 9900 Subsystem 66 Chapter 4 Figure 4.13 I/O Device List Panel (Step 10) Figure 4.14 Add Device Panel (Step 11) Hitachi Lightning 9900 User and Reference Guide 67 Figure 4.15 Device / Processor Definition Panel Selecting the Processor ID (Step 12) Figure 4.16 Define Device / Processor Panel (Step 13) Configuring and Using the 9900 Subsystem 68 Chapter 4 Figure 4.17 Device / Processor Definition Panel (Step 14) Figure 4.18 Define Device to Operating System Configuration (Step 15) Hitachi Lightning 9900 User and Reference Guide 69 Figure 4.19 Define Device Parameters / Features Panel (Step 16) Figure 4.20 Update Serial Number, Description and VOLSER Panel (Step 18) 4.2.3 Defining the 9900 to VM/ESA Systems 4.2.4 Defining the 9900 to TPF 4.3 S/390 Operations 4.3.1 Initializing the LVIs 4.3.2 Device Operations: ICKDSF Configuring and Using the 9900 Subsystem 72 Chapter 4 Table 4.6 ICKDSF Commands for 9900 Contrasted to RAMAC 4.3.3 MVS Cache Operations Page 4.3.4 VM/ESA Cache Operations 4.3.5 VSE/ESA Cache Operations 4.4 Open-Systems Configuration 4.4.1 Configuring the Fibre-Channel Ports 4.4.2 Virtual LVI/LUN Devices 4.4.3 LU Size Expansion (LUSE) Devices 4.5 Open Systems Operations 4.5.1 Command Tag Queuing 4.5.2 Host/Application Failover Support 4.5.3 Path Failover Support 4.5.4 Remote SIM (R-SIM) Reporting 4.5.5 SNMP Remote Subsystem Management 4.5.6 NAS and SAN Operations Chapter 5 Planning for Installation and Operation 5.1 User Responsibilities 5.2 Electrical Specifications and Requirements for Three-Phase Subsystems 5.2.1 Internal Cable Diagram CB101 Hitachi Lightning 9900 User and Reference Guide 83 5.2.2 Power Plugs to Disk Array R&S 3754 or 3934 distribution board CB101 5.2.3 Features 5.2.4 Current Rating, Power Plug, Receptacle, and Connector for Three-Phase (60 Hz only) 5.2.5 Input Voltage Tolerances Planning for Installation and Operation 86 Chapter 5 Figure 5.4 Internal Cable Diagram of a Single-Phase 9960 Subsystem Page 5.3.2 Power Plugs R&S3743 or 3913 Hitachi Lightning 9900 User and Reference Guide 89 200/220/230/240V AC Power to 9910 to Controller Provided with DKC-F410I-1EC Planning for Installation and Operation 90 Chapter 5 to Disk Array to Disk Array 5.3.3 Features 5.3.4 Current Rating, Power Plug, Receptacle, and Connector for Single-Phase (60 Hz only) 5.3.5 Input Voltage Tolerances 5.4 Dimensions and Weight Planning for Installation and Operation 94 Chapter 5 Table 5.7 9900 Physical Specifications Hitachi Lightning 9900 User and Reference Guide 95 Table 5.8 9960 Frame and Component Weights Table 5.9 9960 & 9910 Subsystem Weights 5.5 Floor Loading and Cable Routing Requirements 5.5.1 Service Clearance Requirements Page Page Page Page 5.5.2 Minimum Subsystem Disk Configuration 53.1" Page Planning for Installation and Operation 104 Chapter 5 Figure 5.21 9910 Disk Subsystem All Configurations (inches) Hitachi Lightning 9900 User and Reference Guide 105 5.5.3 Floor Load Rating Table 5.11 Floor Load Rating for 9960 Controller with 1 Disk Array GG G GG Hitachi Lightning 9900 User and Reference Guide 107 Table 5.12 Floor Load Rating for 9960 Controller with 4 Disk Arrays G G GG G G Required Clearance (a+b) Clearance (C) in meters (feet) Page Hitachi Lightning 9900 User and Reference Guide 109 5.5.4 Cable Requirements Planning for Installation and Operation 110 Chapter 5 5.6 Channel Specifications and Requirements Table 5.16 Fibre-Channel Port Information 5.7 Environmental Specifications and Requirements 5.7.1 Temperature and Humidity Requirements 5.7.2 Power Consumption and Heat Output Specifications Planning for Installation and Operation 112 Chapter 5 Table 5.18 9910/9960 Component Power and Heat Output Specifications Table 5.19 9900 Subsystem Power and Heat Output Specifications 5.7.3 Loudness 5.7.4 Air Flow Requirements 5.7.5 Vibration and Shock Tolerances Chapter 6 Troubleshooting 6.1 Troubleshooting 6.2 Service Information Messages (SIMs) 6.3 Calling the Hitachi Data Systems Support Center Page Hitachi Lightning 9900 User and Reference Guide 119 Appendix A Unit Conversions Page Acronyms and Abbreviations