Manuals / Compaq / Computer Equipment / Laptop

Compaq F500 manual Remove the display hinges, Component replacement procedures

Models: F500

1 120

Download 120 pages 40.7 Kb

Page 53

Image 53

15. Remove the display hinges (2).

NOTE: The display hinges are available using spare part number 433288-001

16. If it is necessary to remove the wireless transceivers and cables, remove the Phillips PM2.0×4.0 screw (1) that secures each transceiver to the display enclosure.

17. Remove the wireless antenna cables from the clips (2) built into the display enclosure.

18. Detach the wireless antenna transceivers (3) from the display enclosure.

19. Remove the wireless antenna cables (4) from the display enclosure.

NOTE: The wireless antennae are included with the display enclosure and are also available using spare part number 431398-001.

Reverse this procedure to reassemble and install the display assembly.

Component replacement procedures 47

Page 53

Image 53

Compaq F500 manual Remove the display hinges, NOTE The display hinges are available using spare part number

Contents

Compaq Presario F500 Notebook PC Maintenance and Service GuideCopyright 2007 Hewlett-Packard Development Company, L.P Unknown user password Table of contentsRemoval and replacement procedures 1 Product description 2 External component identificationScrew listing Setup UtilitySpecifications 10 Connector pin assignments 9 Backup and RecoveryPower cord set requirements RecyclingPage Description 1 Product descriptionCategory Description 2 Chapter 1 Product descriptionCategory Serviceability PreinstalledBattery system CategoryTop components 2 External component identificationPointing devices ComponentComponent KeysFunction num lock key6 Chapter 2 External component identification Front componentsComponent FunctionRight-side components Right-side componentsComponent Function8 Chapter 2 External component identification Left-side componentsComponent Functiona warning message, remove the device to restore Bottom componentsComponent Function3 Unknown user password Serial number location 4 Illustrated parts catalogand wireless antenna transceivers and cables Computer major componentsDescription Spare part numberDescription Fan/heat sink assembly includes thermal padsSpare part number Keyboards14 Chapter 4 Illustrated parts catalog 6-cell, 2.20-Ah batteryDescription Spare part numberSpare part number Display assembly componentsDescription Item Description Plastics KitSpare part number Plastics KitMiscellaneous parts Mass storage devicesDescription Spare part numberTV tuner remote control HP Remote Control II PlusWired optical mouse Power cordsSequential part number listing Sequential part number listingSpare part number DescriptionDescription 20 Chapter 4 Illustrated parts catalogSpare part number Description Sequential part number listingSpare part number Preliminary replacement requirements 5 Removal and replacement proceduresService considerations Tools requiredDrive handling Cables and connectorsElectrostatic discharge damage Grounding guidelinesWorkstation guidelines Packaging and transporting guidelinesEquipment guidelines Serial number Component replacement proceduresBattery Hard drive 30 Chapter 5 Removal and replacement procedures Reverse this procedure to reassemble and install the hard drive6. Remove the hard drive 2 from the hard drive bay 8. Lift the bracket 2 straight up to remove it from the hard driveMemory module Computer feet32 Chapter 5 Removal and replacement procedures Reverse this procedure to install a memory module3. Lift the left side of the cover 2 and swing it to the right 4. Remove the memory module compartment coverRTC battery WLAN module Optical drive 36 Chapter 5 Removal and replacement procedures Reverse this procedure to reassemble and install the optical drive5. Remove the optical drive 8. Remove the optical drive bracketSwitch cover 38 Chapter 5 Removal and replacement procedures 7. Remove the switch coverReverse this procedure to install the switch cover Keyboard 5. Lift the rear edge of the keyboard 1 until it rests at an angle 9. Remove the keyboard Reverse this procedure to install the keyboard40 Chapter 5 Removal and replacement procedures Power button board 42 Chapter 5 Removal and replacement procedures 5. Remove the power button boardReverse this procedure to install the power button board b. Keyboard see Keyboard on page Display assemblya. Switch cover see Switch cover on page 44 Chapter 5 Removal and replacement procedures 4. Remove the display assembly1 Four covers on the top edge of the bezel 2 Two covers on the lower bezel corners8. Remove the display bezel NOTE The display bezel is available using spare part numberComponent replacement procedures NOTE The display panel is available using spare part number NOTE The display inverter is available using spare part number46 Chapter 5 Removal and replacement procedures 11. Remove the display inverter19. Remove the wireless antenna cables 4 from the display enclosure NOTE The display hinges are available using spare part numberReverse this procedure to reassemble and install the display assembly Component replacement proceduresTop cover Component replacement procedures 1 Power button board cable 2 TouchPad cable3. Remove the following screws and standoffs 1 Three Phillips PM2.5×4.0 screws 2 Six Phillips PM2.5×5.0 screwsAudio board 4. Remove the battery see Battery on page USB/power connector board Component replacement procedures Reverse this procedure to install the USB/power connector boardSystem board Component replacement procedures 56 Chapter 5 Removal and replacement procedures Reverse this procedure to install the system boardFan/heat sink assembly 58 Chapter 5 Removal and replacement procedures 4. Remove the fan/heat sink assemblyReverse this procedure to install the fan/heat sink assembly Processor Reverse this procedure to install the processor 4 embossed on the processor socket when you install the processor60 Chapter 5 Removal and replacement procedures 2. Lift the processor 2 straight up and remove itStarting the Setup Utility 6 Setup UtilityDisplaying system information Changing the language of the Setup UtilityNavigating and selecting in the Setup Utility 2. Select Exit Load Setup Defaults, and then press enter Restoring default settings in the Setup UtilityUsing advanced Setup Utility features Setup Utility menus Closing the Setup UtilityMain menu Security menuDiagnostics menu System Configuration menuSelect To do thisMetric 7 SpecificationsComputer specifications 15.4-inch, WXGA BrightView display specifications 15.4-inch, WXGA BrightView display specificationsMetric Metric68 Chapter 7 Specifications Hard drive specifications120-GB 100-GBApplicable disc 70 Chapter 7 Specifications System DMA specificationsHardware DMA System functionSystem function System interrupt specificationsHardware IRQ 72 Chapter 7 Specifications System I/O address specificationsSystem function shipping configuration I/O address hexI/O address hex System I/O address specificationsSystem function shipping configuration 74 Chapter 7 Specifications System memory map specificationsSize Memory address8 Screw listing Phillips PM2.0×5.0 captive screw Where usedColor Phillips PM3.0×3.0 screwQuantity LengthPhillips PM2.0×3.0 screw Phillips PM2.0×3.0 screw Where used Phillips PM2.5×7.0 screwPhillips PM2.5×7.0 screw Color Phillips PM2.5×10.0 screwQuantity LengthWhere used Phillips PM2.5×5.0 Screw84 Chapter 8 Screw listing Where usedColor Phillips PM2.0×4.0 ScrewQuantity LengthPhillips PM2.5×4.0 screw Phillips PM2.5×4.0 screw Color Hex HM5.0×7.0 StandoffQuantity LengthColor Phillips PM2.0×6.0 screwQuantity LengthColor Phillips PM2.5×5.0 captive screwQuantity LengthRecovering system information 9 Backup and RecoveryWhen to back up Backing up your informationWhen to create restore points Using system restore pointsCreate a system restore point Restore to a previous date and timeReinstalling software programs and drivers Creating recovery discs1. Select Start All Programs Recovery Manager Recovery Manager 3. Click Recovery disc creation, and then click NextReinstalling preinstalled programs and drivers Performing a recoveryReinstalling programs from discs a. Select Start Control Panel Programs Uninstall a programRecovering from the recovery discs Deleting the recovery partition on the hard driveRecovering from the partition on the hard drive Select Start All Programs Recovery Manager Recovery ManagerSelect Start Help and Support Updating reinstalled softwareAudio-out headphone 10 Connector pin assignmentsAudio-in microphone SignalSignal External monitor98 Chapter 10 Connector pin assignments RJ-45 network RJ-11 modemSignal SignalUniversal Serial Bus S-Video-out100 Chapter 10 Connector pin assignments SignalRequirements for all countries or regions 11 Power cord set requirements102 Chapter 11 Power cord set requirements Requirements for specific countries or regionsCountry/region Accredited agency12 Recycling BatteryDisplay Display Perform the following steps to disassemble the display assembly3. Remove the display bezel 106 Chapter 12 Recycling 6. Remove the display panel assembly 2 from the display enclosure7. Turn the display panel assembly upside down 12. Lift the top edge of the backlight cover 2 and swing it forward 10. Remove the display panel frame 2 from the display panel13. Remove the backlight cover 14. Turn the display panel right-side up108 Chapter 12 Recycling 16. Turn the display panel upside down17. Remove the backlight frame from the display panel 19. Disconnect the display cable 1 from the LCD panel 18. Slide the backlight out of the backlight frame21. Release the LCD panel 3 from the display rear panel 23. Remove the LCD panel 24. Recycle the LCD panel and backlightIndex Ethernet, product description Page static-shielding materials system DMAsystem board system information