Manuals / Compaq / Computer Equipment / Laptop

Compaq F500 manual NOTE The display inverter is available using spare part number

Models: F500

1 120

Download 120 pages 40.7 Kb

Page 52

Image 52

10. Disconnect the display panel cable (2) and the backlight cable (3) from the inverter.

NOTE: The display inverter is available using spare part number 431391-001.

11. Remove the display inverter.

12. If it is necessary to remove the display panel, remove the six Phillips PM2.5×5.0 screws (1) that secure the display panel to the display enclosure.

13. Remove the display panel (2) from the display enclosure.

NOTE: The display panel is available using spare part number 442887-001.

14. If it necessary to remove the display hinges, remove the two Phillips PM2.0×3.0 screws (1) that secure each hinge to the display panel.

46 Chapter 5 Removal and replacement procedures

Page 52

Image 52

Compaq F500 manual NOTE The display inverter is available using spare part number, Remove the display inverter

Contents

Maintenance and Service Guide Compaq Presario F500 Notebook PCCopyright 2007 Hewlett-Packard Development Company, L.P Table of contents Unknown user passwordRemoval and replacement procedures 1 Product description 2 External component identificationSpecifications Setup UtilityScrew listing 9 Backup and Recovery 10 Connector pin assignmentsPower cord set requirements RecyclingPage Category 1 Product descriptionDescription Category 2 Chapter 1 Product descriptionDescription Preinstalled ServiceabilityBattery system Category2 External component identification Top componentsPointing devices ComponentKeys ComponentFunction num lock keyFront components 6 Chapter 2 External component identificationComponent FunctionRight-side components Right-side componentsComponent FunctionLeft-side components 8 Chapter 2 External component identificationComponent FunctionBottom components a warning message, remove the device to restoreComponent Function3 Unknown user password 4 Illustrated parts catalog Serial number locationComputer major components and wireless antenna transceivers and cablesDescription Spare part numberFan/heat sink assembly includes thermal pads DescriptionSpare part number Keyboards6-cell, 2.20-Ah battery 14 Chapter 4 Illustrated parts catalogDescription Spare part numberDescription Display assembly componentsSpare part number Plastics Kit Item DescriptionSpare part number Plastics KitMass storage devices Miscellaneous partsDescription Spare part numberHP Remote Control II Plus TV tuner remote controlWired optical mouse Power cordsSequential part number listing Sequential part number listingSpare part number DescriptionSpare part number 20 Chapter 4 Illustrated parts catalogDescription Spare part number Sequential part number listingDescription 5 Removal and replacement procedures Preliminary replacement requirementsService considerations Tools requiredCables and connectors Drive handlingGrounding guidelines Electrostatic discharge damagePackaging and transporting guidelines Workstation guidelinesEquipment guidelines Component replacement procedures Serial numberBattery Hard drive Reverse this procedure to reassemble and install the hard drive 30 Chapter 5 Removal and replacement procedures6. Remove the hard drive 2 from the hard drive bay 8. Lift the bracket 2 straight up to remove it from the hard driveComputer feet Memory moduleReverse this procedure to install a memory module 32 Chapter 5 Removal and replacement procedures3. Lift the left side of the cover 2 and swing it to the right 4. Remove the memory module compartment coverRTC battery WLAN module Optical drive Reverse this procedure to reassemble and install the optical drive 36 Chapter 5 Removal and replacement procedures5. Remove the optical drive 8. Remove the optical drive bracketSwitch cover Reverse this procedure to install the switch cover 7. Remove the switch cover38 Chapter 5 Removal and replacement procedures Keyboard 40 Chapter 5 Removal and replacement procedures 9. Remove the keyboard Reverse this procedure to install the keyboard5. Lift the rear edge of the keyboard 1 until it rests at an angle Power button board Reverse this procedure to install the power button board 5. Remove the power button board42 Chapter 5 Removal and replacement procedures a. Switch cover see Switch cover on page Display assemblyb. Keyboard see Keyboard on page 4. Remove the display assembly 44 Chapter 5 Removal and replacement procedures1 Four covers on the top edge of the bezel 2 Two covers on the lower bezel cornersComponent replacement procedures NOTE The display bezel is available using spare part number8. Remove the display bezel NOTE The display inverter is available using spare part number NOTE The display panel is available using spare part number46 Chapter 5 Removal and replacement procedures 11. Remove the display inverterNOTE The display hinges are available using spare part number 19. Remove the wireless antenna cables 4 from the display enclosureReverse this procedure to reassemble and install the display assembly Component replacement proceduresTop cover 1 Power button board cable 2 TouchPad cable Component replacement procedures3. Remove the following screws and standoffs 1 Three Phillips PM2.5×4.0 screws 2 Six Phillips PM2.5×5.0 screwsAudio board 4. Remove the battery see Battery on page USB/power connector board Reverse this procedure to install the USB/power connector board Component replacement proceduresSystem board Component replacement procedures Reverse this procedure to install the system board 56 Chapter 5 Removal and replacement proceduresFan/heat sink assembly Reverse this procedure to install the fan/heat sink assembly 4. Remove the fan/heat sink assembly58 Chapter 5 Removal and replacement procedures Processor 4 embossed on the processor socket when you install the processor Reverse this procedure to install the processor60 Chapter 5 Removal and replacement procedures 2. Lift the processor 2 straight up and remove it6 Setup Utility Starting the Setup UtilityNavigating and selecting in the Setup Utility Changing the language of the Setup UtilityDisplaying system information Using advanced Setup Utility features Restoring default settings in the Setup Utility2. Select Exit Load Setup Defaults, and then press enter Closing the Setup Utility Setup Utility menusMain menu Security menuSystem Configuration menu Diagnostics menuSelect To do thisComputer specifications 7 SpecificationsMetric 15.4-inch, WXGA BrightView display specifications 15.4-inch, WXGA BrightView display specificationsMetric MetricHard drive specifications 68 Chapter 7 Specifications120-GB 100-GBApplicable disc System DMA specifications 70 Chapter 7 SpecificationsHardware DMA System functionHardware IRQ System interrupt specificationsSystem function System I/O address specifications 72 Chapter 7 SpecificationsSystem function shipping configuration I/O address hexSystem function shipping configuration System I/O address specificationsI/O address hex System memory map specifications 74 Chapter 7 SpecificationsSize Memory address8 Screw listing Where used Phillips PM2.0×5.0 captive screwPhillips PM3.0×3.0 screw ColorQuantity LengthPhillips PM2.0×3.0 screw Phillips PM2.0×3.0 screw Phillips PM2.5×7.0 screw Where usedPhillips PM2.5×7.0 screw Phillips PM2.5×10.0 screw ColorQuantity LengthPhillips PM2.5×5.0 Screw Where usedWhere used 84 Chapter 8 Screw listingPhillips PM2.0×4.0 Screw ColorQuantity LengthPhillips PM2.5×4.0 screw Phillips PM2.5×4.0 screw Hex HM5.0×7.0 Standoff ColorQuantity LengthPhillips PM2.0×6.0 screw ColorQuantity LengthPhillips PM2.5×5.0 captive screw ColorQuantity Length9 Backup and Recovery Recovering system informationWhen to back up Backing up your informationUsing system restore points When to create restore pointsCreate a system restore point Restore to a previous date and timeCreating recovery discs Reinstalling software programs and drivers1. Select Start All Programs Recovery Manager Recovery Manager 3. Click Recovery disc creation, and then click NextPerforming a recovery Reinstalling preinstalled programs and driversReinstalling programs from discs a. Select Start Control Panel Programs Uninstall a programDeleting the recovery partition on the hard drive Recovering from the recovery discsRecovering from the partition on the hard drive Select Start All Programs Recovery Manager Recovery ManagerUpdating reinstalled software Select Start Help and Support10 Connector pin assignments Audio-out headphoneAudio-in microphone Signal98 Chapter 10 Connector pin assignments External monitorSignal RJ-11 modem RJ-45 networkSignal SignalS-Video-out Universal Serial Bus100 Chapter 10 Connector pin assignments Signal11 Power cord set requirements Requirements for all countries or regionsRequirements for specific countries or regions 102 Chapter 11 Power cord set requirementsCountry/region Accredited agencyBattery 12 RecyclingDisplay 3. Remove the display bezel Perform the following steps to disassemble the display assemblyDisplay 7. Turn the display panel assembly upside down 6. Remove the display panel assembly 2 from the display enclosure106 Chapter 12 Recycling 10. Remove the display panel frame 2 from the display panel 12. Lift the top edge of the backlight cover 2 and swing it forward13. Remove the backlight cover 14. Turn the display panel right-side up17. Remove the backlight frame from the display panel 16. Turn the display panel upside down108 Chapter 12 Recycling 18. Slide the backlight out of the backlight frame 19. Disconnect the display cable 1 from the LCD panel21. Release the LCD panel 3 from the display rear panel 23. Remove the LCD panel 24. Recycle the LCD panel and backlightIndex Ethernet, product description Page system DMA static-shielding materialssystem board system information