Manuals / Compaq / Computer Equipment / Laptop

Compaq F500 Remove the display bezel, NOTE The display bezel is available using spare part number

Models: F500

1 120

Page 51

6. Remove the eight Phillips PM2.5×7.0 screws that secure the display bezel to the display assembly.

NOTE: All screws used to secure display assembly internal subcomponents are available in the Display Screw Kit, spare part number 431400-001.

7. Flex the inside edges of the left and right sides (1) and the top and bottom sides (2) of the display bezel until the bezel disengages from the display enclosure.

8. Remove the display bezel (3).

NOTE: The display bezel is available using spare part number 433284-001.

9. If it is necessary to replace the display inverter, release the inverter (1) from the display enclosure as far as the display panel cable and backlight cable will allow.

Component replacement procedures 45

Page 51

Image 51

Compaq F500 manual Remove the display bezel, NOTE The display bezel is available using spare part number

Contents

Compaq Presario F500 Notebook PC Maintenance and Service GuideCopyright 2007 Hewlett-Packard Development Company, L.P 1 Product description 2 External component identification Table of contentsUnknown user password Removal and replacement proceduresSetup Utility SpecificationsScrew listing Recycling 9 Backup and Recovery10 Connector pin assignments Power cord set requirementsPage 1 Product description CategoryDescription 2 Chapter 1 Product description CategoryDescription Category PreinstalledServiceability Battery systemComponent 2 External component identificationTop components Pointing devicesnum lock key KeysComponent FunctionFunction Front components6 Chapter 2 External component identification ComponentFunction Right-side componentsRight-side components ComponentFunction Left-side components8 Chapter 2 External component identification ComponentFunction Bottom componentsa warning message, remove the device to restore Component3 Unknown user password Serial number location 4 Illustrated parts catalogSpare part number Computer major componentsand wireless antenna transceivers and cables DescriptionKeyboards Fan/heat sink assembly includes thermal padsDescription Spare part numberSpare part number 6-cell, 2.20-Ah battery14 Chapter 4 Illustrated parts catalog DescriptionDisplay assembly components DescriptionSpare part number Plastics Kit Plastics KitItem Description Spare part numberSpare part number Mass storage devicesMiscellaneous parts DescriptionPower cords HP Remote Control II PlusTV tuner remote control Wired optical mouseDescription Sequential part number listingSequential part number listing Spare part number20 Chapter 4 Illustrated parts catalog Spare part numberDescription Sequential part number listing Spare part numberDescription Tools required 5 Removal and replacement proceduresPreliminary replacement requirements Service considerationsDrive handling Cables and connectorsElectrostatic discharge damage Grounding guidelinesWorkstation guidelines Packaging and transporting guidelinesEquipment guidelines Serial number Component replacement proceduresBattery Hard drive 8. Lift the bracket 2 straight up to remove it from the hard drive Reverse this procedure to reassemble and install the hard drive30 Chapter 5 Removal and replacement procedures 6. Remove the hard drive 2 from the hard drive bayMemory module Computer feet4. Remove the memory module compartment cover Reverse this procedure to install a memory module32 Chapter 5 Removal and replacement procedures 3. Lift the left side of the cover 2 and swing it to the rightRTC battery WLAN module Optical drive 8. Remove the optical drive bracket Reverse this procedure to reassemble and install the optical drive36 Chapter 5 Removal and replacement procedures 5. Remove the optical driveSwitch cover 7. Remove the switch cover Reverse this procedure to install the switch cover38 Chapter 5 Removal and replacement procedures Keyboard 9. Remove the keyboard Reverse this procedure to install the keyboard 40 Chapter 5 Removal and replacement procedures5. Lift the rear edge of the keyboard 1 until it rests at an angle Power button board 5. Remove the power button board Reverse this procedure to install the power button board42 Chapter 5 Removal and replacement procedures Display assembly a. Switch cover see Switch cover on pageb. Keyboard see Keyboard on page 2 Two covers on the lower bezel corners 4. Remove the display assembly44 Chapter 5 Removal and replacement procedures 1 Four covers on the top edge of the bezelNOTE The display bezel is available using spare part number Component replacement procedures8. Remove the display bezel 11. Remove the display inverter NOTE The display inverter is available using spare part numberNOTE The display panel is available using spare part number 46 Chapter 5 Removal and replacement proceduresComponent replacement procedures NOTE The display hinges are available using spare part number19. Remove the wireless antenna cables 4 from the display enclosure Reverse this procedure to reassemble and install the display assemblyTop cover 1 Three Phillips PM2.5×4.0 screws 2 Six Phillips PM2.5×5.0 screws 1 Power button board cable 2 TouchPad cableComponent replacement procedures 3. Remove the following screws and standoffsAudio board 4. Remove the battery see Battery on page USB/power connector board Component replacement procedures Reverse this procedure to install the USB/power connector boardSystem board Component replacement procedures 56 Chapter 5 Removal and replacement procedures Reverse this procedure to install the system boardFan/heat sink assembly 4. Remove the fan/heat sink assembly Reverse this procedure to install the fan/heat sink assembly58 Chapter 5 Removal and replacement procedures Processor 2. Lift the processor 2 straight up and remove it 4 embossed on the processor socket when you install the processorReverse this procedure to install the processor 60 Chapter 5 Removal and replacement proceduresStarting the Setup Utility 6 Setup UtilityChanging the language of the Setup Utility Navigating and selecting in the Setup UtilityDisplaying system information Restoring default settings in the Setup Utility Using advanced Setup Utility features2. Select Exit Load Setup Defaults, and then press enter Security menu Closing the Setup UtilitySetup Utility menus Main menuTo do this System Configuration menuDiagnostics menu Select7 Specifications Computer specificationsMetric Metric 15.4-inch, WXGA BrightView display specifications15.4-inch, WXGA BrightView display specifications Metric100-GB Hard drive specifications68 Chapter 7 Specifications 120-GBApplicable disc System function System DMA specifications70 Chapter 7 Specifications Hardware DMASystem interrupt specifications Hardware IRQSystem function I/O address hex System I/O address specifications72 Chapter 7 Specifications System function shipping configurationSystem I/O address specifications System function shipping configurationI/O address hex Memory address System memory map specifications74 Chapter 7 Specifications Size8 Screw listing Phillips PM2.0×5.0 captive screw Where usedLength Phillips PM3.0×3.0 screwColor QuantityPhillips PM2.0×3.0 screw Phillips PM2.0×3.0 screw Where used Phillips PM2.5×7.0 screwPhillips PM2.5×7.0 screw Length Phillips PM2.5×10.0 screwColor QuantityWhere used Phillips PM2.5×5.0 Screw84 Chapter 8 Screw listing Where usedLength Phillips PM2.0×4.0 ScrewColor QuantityPhillips PM2.5×4.0 screw Phillips PM2.5×4.0 screw Length Hex HM5.0×7.0 StandoffColor QuantityLength Phillips PM2.0×6.0 screwColor QuantityLength Phillips PM2.5×5.0 captive screwColor QuantityBacking up your information 9 Backup and RecoveryRecovering system information When to back upRestore to a previous date and time Using system restore pointsWhen to create restore points Create a system restore point3. Click Recovery disc creation, and then click Next Creating recovery discsReinstalling software programs and drivers 1. Select Start All Programs Recovery Manager Recovery Managera. Select Start Control Panel Programs Uninstall a program Performing a recoveryReinstalling preinstalled programs and drivers Reinstalling programs from discsSelect Start All Programs Recovery Manager Recovery Manager Deleting the recovery partition on the hard driveRecovering from the recovery discs Recovering from the partition on the hard driveSelect Start Help and Support Updating reinstalled softwareSignal 10 Connector pin assignmentsAudio-out headphone Audio-in microphoneExternal monitor 98 Chapter 10 Connector pin assignmentsSignal Signal RJ-11 modemRJ-45 network SignalSignal S-Video-outUniversal Serial Bus 100 Chapter 10 Connector pin assignmentsRequirements for all countries or regions 11 Power cord set requirementsAccredited agency Requirements for specific countries or regions102 Chapter 11 Power cord set requirements Country/region12 Recycling BatteryDisplay Perform the following steps to disassemble the display assembly 3. Remove the display bezelDisplay 6. Remove the display panel assembly 2 from the display enclosure 7. Turn the display panel assembly upside down106 Chapter 12 Recycling 14. Turn the display panel right-side up 10. Remove the display panel frame 2 from the display panel12. Lift the top edge of the backlight cover 2 and swing it forward 13. Remove the backlight cover16. Turn the display panel upside down 17. Remove the backlight frame from the display panel108 Chapter 12 Recycling 23. Remove the LCD panel 24. Recycle the LCD panel and backlight 18. Slide the backlight out of the backlight frame19. Disconnect the display cable 1 from the LCD panel 21. Release the LCD panel 3 from the display rear panelIndex Ethernet, product description Page system information system DMAstatic-shielding materials system board