SV278/SV278W I.S. 10/21/03 11:12 AM Page 3
•This motion activated twin floodlight should be installed by persons with experience in house- hold wiring or by a qualified electrician. The electrical system, and the method of electrically connecting the fixture to it, must be in accordance with the National Electrical Code and local building codes.
•Use only with a 100 watt or smaller wattage bulb. Installing a bulb of higher wattage could create a fire hazard. Use of a higher wattage bulb will void the warranty.
•Never touch the bulb with your bare hands, as oil from your skin can cause premature failure. Always handle the bulb with gloves or a soft cloth.
•For supply connections, use wire rated at least 75 degrees C.
•For proper operation and protection against damage, the motion sensor head adjustment knobs must be facing the ground.
•In the event of lens breakage, contact Customer Service for ordering assistance.
•Disassembly of your fixture will void the warranty.
SAVE THESE INSTRUCTIONS.
For best results |
|
• Install your fixture |
|
sensitive above 12 feet). |
|
• Locate fixture so motion moves across detection zone (L). |
|
• Locate fixture away from heat producing sources to prevent |
|
false triggering. Also be very careful not to include objects such as win- | L |
dows, white walls and water in the detection zone whenever possible. |
|
•Locate fixture away from moving objects such as trees and street traffic.
•Do not install more than one motion detector on one wall switch.
Installing your bulb
Step 1: Remove the lens cover by twisting it
Step 2: Using gloves or a soft cloth, gently insert bulb into housing. NOTE: Align two pins
located on the sides of the bulb with two small | Your fixture mounts to the | ||
slots in the socket, press bulb into spring loaded | |||
socket and twist a half turn clockwise, until firmly | following standard junction boxes: | ||
seated. Repeat this procedure for the other light. |
|
| |
Step 3: Replace the lens (making sure the gasket is in |
|
| |
place) by aligning the notches on the housing with |
|
| |
the cover and pressing while turning | Round | Rectangular (horizontal) Octagonal | |
clockwise until seated. | |||
|
| ||
ENGLISH
Mounting your fixture
Step 1: Turn off the power at the main fuse/breaker box.
Step 2: Line up the holes on the mounting bracket with the holes on your junction box. Using either (2) #6 screws or (2) #8 screws (depending on size of the holes in your junction box), attach the mounting bracket to your junction box (M).
Step 3: Hang one end of the mounting hook onto the mounting bracket (using the hole in the bracket, see drawing), and hang the light fixture on the other end of the mounting hook. NOTE: Carefully hang the fixture at the base of the lampholder assembly as shown. This will
Step 4: Thread fixture wires through coverplate gasket.
Step 5: If the supply wires coming from your house are solid, you can use the
fixture. NOTE: Quick connectors can only be used with solid wire supply leads. Simply insert the black supply wire from your house into the quick connector with black wire coming from the fixture.
Repeat for house white wire, matching to the connector with the white wire. Push both wires firmly into holes to insure that they are seated properly and securely (N). It’s that easy! Proceed to Step 7.
Step 6: If the supply wires coming from your house are stranded, remove the quick connectors from the end of the light fixture wires by turning them repeatedly from left to right while pulling. Repeat until they are both removed. Remember: Quick connectors can only be used with solid wire supply leads. Do not attempt to use with other electrical fixtures! These connectors are designed to withstand the temperature and Voltage requirements of this Regent product only. Once the connectors have been removed, connect black wire to house black wire and connect white wire to house white wire using the wire nuts provided.
M
(wall mount)
(eave mount)
Prewired quick connector
N
3
