Parts LiST and Schematic for Stand

10 in. TABLE SAW					MODEL NO. 137.248850
PARTS LiST AND SCHEMATIC FOR STAND
LB.	Description		SIZE		QTY
0J68	FLAT WASHER		cp5_10-1		3
0K82	CR. RE. COUNT HD. TAPPING SCREW		M5"12-16		3
0KB3	CR. RE. PAN HD. TAPPING	SCREW	M4"18-8		2
0KBA	CR. RE. PAN HD. TAPPING	SCREW	M5"16-12		3
0KMS	HEX. NUT		M6"1.0	T=5	1
0KMY	HEX. NUT		M8"1.25	T=6.5	1
0KRL	U-TYPE NUT				3
0VJX	HEX. HD. SCREW AND WASHER		M8"1.25-30		4
27CC	CR. RE. PAN HD. TAPPING	SCREW	M5"16-6		2
2ETN	BOTTOM BRACKET DOOR				1
2ETP	FLOOR PLATE				1
2ETQ	PLUNGER HOUSING				1
2ETR	BOTTOM BRACKET				1
2ETS	CUSHION				3
2ETT	SETPLATE				1
2EU3	LEVELING PAD				1
2EU4	LEVELING WASHER				1
2EW0	HARDWARE BAG ASS'Y				1
2FS2	CR. RE. TRUSS HD. TAPPING	SCREW	M5"12-12		13
2FYJ	PLUNGER				1
2FYK	HINGE				1
2FYL	PiN				1
2FYN	PLATE CLAMP				1

OVJX 4

2ETR

_FYL

OKMS

2FYN

OKMY

Page 27

Image 27

Craftsman 137.24885 operating instructions Parts LiST and Schematic for Stand

Contents

Visit our Craftsman website Safety Instructions Motor ONE=YEAR Full Warranty on Craftsman ToolSection Lead from lead-based paints USE only Recommended Accessories Dang ER Look for this symbol that Never USE the Miter Gauge and Fence Simultaneously Never Perform ANY Operation Grounding iNSTRUCTiONS Quantity = Only use atackable dadoes Abcd Jklm Page RESIN- a stickysapthathashardened ARBOR- Theshaftonwhichthebladeordadois mountedBLADEELEVATIONHANDWHEEL- Raisesand lowerstheblade COMPOUNDCUT- Asimultaneousbevelandmiter cut Damage the SAW Base Tightenhardware Placethestandona levelsurfaceandadjusttheASSEMBUNGSTANDFIG.A Assemble Table SAW to Stand FIG. B RIP Fence FIG. D Installing and Changing the Blade FIG. E, F, GMountsawonworksurface Blade Raising Handwheel FIG. C Proper insert in place. Use the original installed Blade Guard Assembly FIG. H, I, JTo avoid possible injury and damage to Serious injury Installing Table Side Extensions FIG. L, L=IInstalling Rightside Table Extension Wing FIG. K Avoid Kickbacks FIG. J RIP Fence Indicator Adjustment FIG. N Installing Rear Table Extension FIG, MAdjusting Rear Table Extension RIP Fence Adjustment FIG. N Loosenthebladebevellockknob1andmovethe 900Stop Disconnectthesawfromthepowersource If the blade is partial to left aide Blade Tilting Indicator FIG. TMiter Gauge Adjustment FIG. T=I Rotatethebladebringingthemarkedtoothtothe Overload Protection FIG ON/OFF Switch FIGUsing the Table Extension FIG. W Basicsawoperations Raisetheblade FIG. U Greatly increase the likelihood of injury Usingthe Dust Chute FIG. YTo prevent sawdust buildup inside the saw housing Cutting Operations Always position the larger surface of the workpiece RiPPiNG Small PiecesTo prevent serious injury Enough to cause a severe injury Fig, DD WARNINe Fig. HH DADOCUTSFIG. HH Lubrication Corrective Action Symptom Possible Causes 10 in. Table SAW Schematic SAW Model Parts LiST and Schematic for Stand Page Page =888-SU=HOGAR =800=LE=FOYER

10 in. TABLE SAW

MODEL NO. 137.248850