Craftsman 139.53626SR - I/2HP Radio Controls, Match/Change The Code In Transmitters, 1-91

Radio Controls

EC.C. rules prohibit adjustments to or modification of receiver and transmitter circuitry except for changing the

code setting and replacing the transmitter battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Manufactured under 1 or more of the following U.S. patents: RF.29,525; 4,037.201; 4,750.n8; 4,806,g30. Other patents pending.

Your 53000SR SERIES garage door opener (with RECEIVER 'SR'CODE BUTTON) has been factory set to operate with the LARGE push button on the transmitter. The 3-function transmitter(s) can also activate additional garage door openers and/or light controls - 53000 and/or 53000SR SERIES.

Instructions are given below for matching the code in all transmitters, changing your code selection or using the transmitter(s) with other receivers.

MATCH/CHANGE THE CODE IN TRANSMITTER(S)

SET CODE SWITCHES IN ALL TRANSMITTERS TO MATCHING POSITIONS

1.Locate the code switches in transmitter(s), either by sliding battery compartment cover down or by removing cover screw and carefully turning case top over.

2.With a pen or a screwdriver, change the setting of one or more switch (to a (+), (-) or (0) position).

NOTE: Code switches 2 through 9 in ALL transmitters used to operate s receiver must be set to match. (Code switch 1 on a 3-function transmitter is neutral. Set it to ANY position. It will not affect the code selected).

3-FunctionC:3

Transmitter

SET RECEIVER TO MATCH

53000SR SERIES (WITH RECEIVER CODE BUTTON) Garage Door Openers and Light Controls

(lllustratten A shows • garage door opener receiver)

Standard			3-Function
/F_	_	_	MiniTransmitter

o.1_-

c°dei s.;+l'ch'+ (1-91

TRANSMITTER(S) CODE

53000 SERIES (WITH RECEIVER CODE SWITCHES)

Garage Door Openers and Light Controls

(Illustration B shows s garage door opener receiver)

Push Button (-)

3 FUNCTION	A	GARAGE DOOR
TRANSMITTER	_	OPENER RECEIVER
		(W'dhSR Code	Button)
Select a transmitter	push	RED W_T BU<
button to operate receiver
	...........%%%		%
	l SR	Indicator
	CodeButton Light

3.Press the RECEIVER SR code button on the right side panel of opener (Illustration A). The indicator light will turn ON.

B 3 FUNCTION

TRANSMITTER

Select a b-at-_mitter push button to operate

	receiver
Push Button	(0)
	GARAGE		DOOR
	OPENER	RECEIVER
	(With Code		Switches)
	switch	#1	to position
	that matches			selected
	Slide receiver			code
	transmitter		push button
seWithn,c_i_;Vp_siC_tio#_.	(+,o or-)

receiver will operate with transmitters'

large push button

4.STAND AWAY FROM THE DOOR and press the selected push button on the transmitter. The indicator light will tum OFF and door will move. Receiver and transmitter codes now match and the opener will operate with the selected push button on the transmitter.

NOTE: If transmitter push button is not pressed within 30 seconds, the indicator light will turn OFF. Begin again at Step 3.

TO USE THE TRANSMITTER(S) WITH OTHER 53000SR SERIES RECEIVERS: Select another transmitter push button to operate the Light Control or additional garage door opener. Make sure all transmitters used to operate receiver are set to the same code (Steps I and 2). Repeat Steps 3 and 4.

3.Locate the receiver code switches. Set code switch #1 to match transmitter push button you want to use with that receiver (+), (0) or (-). Refer to illustration 0B).

4.Hold a transmitter (with code switches visible) along- side the receiver. Beginning with RECEIVER code

switch #2, match the position of each transmitter switch.

TO USE THE TRANSMITTER(S) WITH OTHER 53000 SERIES RECEIVERS: Select another transmitter push button to operate the Light Control or additional garage door opener, Make sure all transmitters are set to a match- ing code (Steps 1 and 2). Repeat Steps 3 and 4.

t9