Howtoset-Upyourchipper-Shredder

Spacers:				Housiltg
				Assem aly
				13olt
				3hute
				D .=flector
He](
Nut
Hand
Knob
FIGURE	2.
		Stop
Hopper	!-_F--_	Washer
Pivot _		"_/_	_o
Door	//_	/ "_'_Y_\
/!	II II11!	\/		3pper
//	t l /l_'I_	_		_uiae
//	_,-_\_	_	Release	A.,;sembly

t/ ,_ _t_ J I \llll _ Bar

II /JillXHexBolt

///I \\1 fill 8-3/8"Long

II/ Inset \\1 °Ill Y Flat Washer

///

Guide _

Hex Lock Nut

FIGURE 3.

Hopper Pivot Hopper Asstimbly

Door

	t l pper
		Leaf
Bar		Ilamp
	S .=ction
	Remove T russ
Guide	Screw ant	Nut
Guide	(Asseml de
Assembly	(Asseml de
Assembly	First)
	First)
FIGURE 4.
	Drawstr	ng

.Plunger

FIGURE 5.

WIRE IS DISCONNECTED AND MOVED

,_ AWAYMAKE CERTAINFROM THETHE SPARK PLUG

BEFORE ASSEMBLING THE CHIPPER-

SHREDDER. REFER TO FIGURE 13, PAGE 10.

<'-ATTACHING THE CHUTE DEFLECTOR

•Remove the hand knobs and cupped washers from each side of the discharge opening on the left side of the chipper-shredder.

•Remove hex lock nut, two spacers and hex bolt using two 7/16" wrenches from inside the hinge on top of the housing assembly. Do not remove one spacer from the hex bolt.

•Place the chute deflector in position on the dis- charge opening. Insert hex bolt and spacer through hinge on chute deflector and housing (spacer fits inside of hinge). See figure 2.

•Place second spacer over hex bolt, inside other part of hinge. Secure with hex lock nut. Tighten securely.

•Secure both sides of chute deflector to housing using hand knobs and cupped washers (cupped side

of washers go against chute deflector).

_-ATTACHINGTHE UPPER GUIDE ASSEMBLY

Grasp the upper guide assembly from the sides and squeeze in and slide it over the inlet guide so the edges are under the stop washers. Adjust so the holes in the upper guide assembly are aligned with the holes in the inlet guide. Insert the hex bolt, 8-3/8" long through the upper guide assembly and the inlet guide. Secure with flat washer and lock nut.

NOTE: Make certain the upper guide assembly can pivot by lifting it up until it locks in the raised position. If it does not pivot freely, loosen the hex lock nut a turn or two and test.

<-ATTACHING THE HOPPER ASSEMBLY

Your chipper-shredder has been shipped with the upper leaf ramp section attached to the hopper assembly. See figure 4. Attach the hopper assembly to the upper guide assembly as follows. Be certain to place heads of all truss machine screws inside of hopper assembly.

•Remove one truss machine screw and nut from

each side of hopper assembly as shown in figure 4.

Push hopper pivot door down inside lower part of hopper as you place hopper assembly (both

pieces) inside upper guide assembly. Replace truss screws and nuts just removed, using the hole shown in figure 4, one on each side. Tighten finger tight only.

NOTE: You may have to squeeze in the sides of the hopper to start the screws.

NOTE: If you have difficulty aligning the hole, loosen the two screws on the upper end of the hopper assembly.

•Place the six truss machine screws and nuts found in hardware pack in the remaining holes of hopper assembly, alternating sides of the unit and tighten- ing finger tight only.

•After assembling all eight screws, tighten them securely.

<-ATTACHING THE CATCHER BAG

Your chipper-shredder is equipped with a catcher bag to catch the shredded material.

247.795950 specifications

The Craftsman 247.795950 is a powerful and versatile snow blower designed to tackle the toughest winter conditions. With its robust construction and user-friendly features, it is an excellent choice for homeowners looking to keep their driveways and walkways clear of snow.

One of the standout features of the Craftsman 247.795950 is its strong engine. Powered by a dependable gas engine, this snow blower provides reliable performance, making it capable of clearing heavy snowfalls with ease. The engine is designed for efficient fuel consumption, ensuring that users can get the job done without constantly refueling.

The machine features a 24-inch clearing width, allowing it to clear a wide path in a single pass. This is particularly beneficial for those with larger driveways or property areas, as it reduces the time and effort needed to clear snow. The unit is equipped with an adjustable pitch auger that not only efficiently gathers and throws snow but also allows users to control the distance and direction of the snow discharge.

The Craftsman 247.795950 incorporates innovative technologies to enhance its usability. With its electric start feature, starting the snow blower in cold conditions becomes a hassle-free experience. This eliminates the need for tedious manual pulls while ensuring that the machine is ready to work when you are.

Another significant characteristic is its six-speed transmission, which includes two reverse speeds. This feature allows for greater control when navigating through challenging snow conditions, whether you're moving forward or backward. The ease of maneuverability is further enhanced by its large, heavy-duty tires, which provide excellent traction on slippery surfaces.

The snow blower is also designed with user comfort in mind. Its ergonomic handles are adjustable, allowing users to set them at a comfortable height. This feature reduces fatigue during prolonged use, making snow clearing less of a chore. Additionally, the hand warmers ensure that operators can work comfortably even in frigid temperatures.

Overall, the Craftsman 247.795950 stands out for its combination of power, efficiency, and user-centric features, making it a reliable tool for managing winter weather challenges. Whether facing light flurries or severe snowfall, this snow blower is engineered to perform efficiently, ensuring that winters are a little easier to navigate. Its durable construction and thoughtful features make it a solid investment for any homeowner.

Craftsman 247.795950 manual Howtoset-Upyourchipper-Shredder, Attachingthe Upper Guide Assembly

Models: 247.795950

Guide _

Hex Lock Nut